Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.

Windows 7: Got a New Case!

14 May 2014   #131
Lady Fitzgerald

Win 7 Ultimate 64 bit

Quote   Quote: Originally Posted by NoN View Post
You combined both....Additional room for components + Good looking PC case.

Great work Lady! I'm amaze how tricky you are to suit the way you want your case to be.
Thanks, NoN!

My System SpecsSystem Spec
14 May 2014   #132

Win 7 Pro x64, Win 10 Pro x64, Linux Light x86

Quote   Quote: Originally Posted by Lady Fitzgerald View Post
I'm no longer dreading cutting out the rest of the top grill in the case because the deed is done. It's kinda crude but, once the shroud and acoustic foam is in, no one will ever see it.

This is what the top of the case looked like after I chewed out most of the grill the other day:

Attachment 317690

It was meatball surgery but it got the worst of it out of my way. I put low tack tape on top to protect the finish and make the layout lines more visible. I had to leave parts of the flange remaining from the grill to give support for the mounting holes because the holes would otherwise be just over the edge of the final opening.

Attachment 317691

Here are the final results after cutting, drilling, and filing. I did a lot of eyeballing since everything is going to be covered up and I'm getting tired of working on this. You can see the tabs (formerly part of the flange that angled down) I had to leave in place to give some "meat" around the holes so the screws won't "blow out". That's about 2.5 hours work (including a few short breaks to rest the Dremel, my hands, and my back).

Attachment 317693

Yay! It fits! I haven't chinched it down but the screws are all in place so I could see if everything fit properly.

Attachment 317694

The shroud has little stainless steel cups that slip into recesses in the plastic sides. They are supposed to be inserted the way shown on the right but I'm not crazy about how that looks plus it forms a pocket that can collect dust and other assorted crud that could be a nuisance to clean. One thing I love about this case it doesn't have hard to clean recesses to collect dust so I didn't like the idea of adding eight of them. On the left, I reversed the cup. That looks better and will not collect "stuff".

Attachment 317695

There are three tabs, like the one shown below, at the bottom of the case on each side to position the case side panels. I had to cut the center tab out on the left side because it was in the way of removing the bottom HDD tray (whoever designed that should be shot...where it hurts!). Fortunately only the outside edges of the outside tabs are needed to position the side panel.

Attachment 317696

I had to cut part of the front tab away because the corner of the tab still got in the way of the HDD tray. I could still wiggle past it but once I shim the cage to eliminate any slack that could allow HDD vibration, I probably wouldn't be able to get the HDD tray out. The notch I cut in the tab will ensure I will be able to get the tray out.

Attachment 317698

I don't think I will need to do anymore surgery so the next step will be to install the acoustic foam. I need to make a shim to go in the recessed area under the PSU where the PSU fan isn't so I can lay acoustic foam over it to act like a gasket around the PSU so dust can't get in. Then I can install the fan hub, PSU, and the fans. Then I get to start modifying/making the PSU cables.
4th picture down ... That looks fantastic Jeannie
My System SpecsSystem Spec
14 May 2014   #133
Lady Fitzgerald

Win 7 Ultimate 64 bit

Thanks, Stephanie!

I'm not going to get much done today; the wind is up again and my allergies are driving me insane. I was up late trying to work out a few details on installing the acoustic foam (the inside of the case is a regular obstacle course). I did install the 140mm lugs on the three exhaust fans this morning and painted the wires and the centers of all the 140mm fans black. Some of the lugs were still a little loosey goosey after tightening the screws so I removed them, brushed on some nail glue, and reinstalled. Problem solved.

I also installed the painted braces on the side panel fans.

Got a New Case!-img_003.jpg

That pretty much takes care of the oil canning problem.

My System SpecsSystem Spec

17 May 2014   #134
Lady Fitzgerald

Win 7 Ultimate 64 bit

Working yesterday and today, I managed to finish installing the acoustic foam on the bottom of the case. I had to play dodgem with the PSU and the third HDD cage, the latter especially being a stinker. Part of the "fun" were all the little holes that had to punched into the foam. Here is a shot of the foam in the bottom of the case.

Got a New Case!-img_0011.jpg

Besides dampening sound, the foam is also sealing up some holes and is serving as gasket material in places. The strip of foam on the lower back corner of the MOBO plate is to seal an leak in that area that the PSU left open. Foam also covers up the portion of the bottom grill that not only wasn't needed by the PSU fan, it also would either let air out of the case or suck it in (at least it would have been filtered). Here is a shot with the PSU in place.

Got a New Case!-img_0012.jpg

It fits pretty snugly. There are no air leaks around that thing now.

I wanted to get as much foam under the third HDD cage as possible, both to damp sound and for appearance sake but I had to trim out quite a bit just to be able to still get the cage in. This is how the case looks with the cage installed.

Got a New Case!-img_0015.jpg

Again, it's a pretty snug fit. I have to hold my mouth just right to get it in there. The two thumbscrews that help to secure the cage are a bit closer to the foam than I like but I had no trouble getting my paw between the cage and the PSU to get at the screws. Of course, there are no cables plugged into the PSU yet. Fortunately, I have no plans to remove the cage once it's in there for keeps after I'm finished modding the case.

Here is a shot of the bottom of the case. I've got the four 3/8" plugs popped in. You can see where I had to use foam to block off part of the PSU grill to seal off what would have been a major air and dust leak. Since I took the photo, I've taken a black paint pen to the bottom of the foam that is showing through the grill to keep dust from sticking to the adhesive and for appearance sake.

Got a New Case!-img_0018.jpg

Here are the standoffs that will support the base of the fan hub for the side panel fans. If I just bolted it down directly to the foam, I never would have gotten it tight nor to stay put.

Got a New Case!-img_0020.jpg

Here is the base bolted down.

Got a New Case!-img_0022.jpg

And here is the hub itself installed in the base. The two side panel fans will plug into the two top connectors on the hub. A cable will connect the horizontal connector to the bottom fan header on the MOBO.

Got a New Case!-img_0025.jpg

Got a New Case!-img_0026.jpg

I also have some shots of the acoustic foam on the top panel but I still need to install some more up there and I suddenly started feeling tired all over (stupid old age) so I'm going to take a nap for now.

My System SpecsSystem Spec
17 May 2014   #135

Windows 10 Pro X64

Great work, I am enjoying the progress you are making.
My System SpecsSystem Spec
17 May 2014   #136
Mellon Head

Win 7 Pro x64/Win 10 Pro x64 dual boot

Looking great so far. I can't wait to see more.
My System SpecsSystem Spec
17 May 2014   #137
Lady Fitzgerald

Win 7 Ultimate 64 bit

Thanks, Dude and Bryan! I'll have some more pics in a few minutes,
My System SpecsSystem Spec
18 May 2014   #138
Lady Fitzgerald

Win 7 Ultimate 64 bit

I attacked the front of the case this afternoon. It wasn't as bad as I was expecting. Here are a couple of shots of the front.

Got a New Case!-img_0002.jpg

Got a New Case!-img_0003.jpg

I did not like or trust the tool free gizmos on the 5.25" cage so I removed them. Screws are much more secure. However, the remaining brackets and extra holes looked pretty ugly so I covered both sides with acoustic foam that I punched clearance holes into for the 5.25" device mounting screws (getting those holes just right The reason there are only four holes punched into the right side of the cage is that's all there were.

I put the modified front fan in to check the fit of the foam around it. 'Tis a bit snug but better that than a bit loose. I have the fan temporarily screwed in until I can get some washers to go under the heads of the screws I'm going to use to keep them from falling through the loops of the front fan grill. That probably won't be until Monday or Tuesday.

The really tricky part was putting in the foam on the front at the top of the case. There was all kinds of "stuff" I had to play dodgem with. I had to temporarily remove that stupid switch housing again to get room to get my fingers in there. Thank God I don't have big hands!

Got a New Case!-img_0006.jpg

I still have the sides of the top of the case to do and the back of the case (both are going to be a bit tricky). However, I'm just about out of acoustic foam. I have another sheet already on order and it should be in Monday or Tuesday. I should also be getting the black fan connector bodies I ordered around the same time so I can replace the ugly white ones on my 140mm fans and get those installed once I get the rest of the foam in.

My System SpecsSystem Spec
18 May 2014   #139
Layback Bear

Windows 10 Pro. 64/ version 1709 Windows 7 Pro/64

You are going to need a little blinking yellow light on top of the computer.
Why; is what you are thinking.
This case is going to be so quiet it will be a indicator when the computer is on. This will remind you to turn the compute off when desired.
No self respecting dust bunny would dare go inside this case.
Lot of great work and ideas.

Who is you supplied of the acoustic foam?
My System SpecsSystem Spec
18 May 2014   #140
Microsoft MVP

Windows 7 Ultimate X64 SP1

You've done a lot Jeannie, the system should really be Cool'n'Quiet and clean.
My System SpecsSystem Spec

 Got a New Case!

Thread Tools

Similar help and support threads
Thread Forum
The Case of the Missing Pillow Case
Please press play to set the right mood as you read. ;) NzlG28B-R8Y The Case of the Missing Pillow Case Today appeared to be a normal day just like any other. I had decided that I should strip the beds and wash the sheets from them since it had been a while and they were starting to...
Chillout Room
new case
I too, am looking for a new case to upgrade. My old one is a Ultra E-Torque mid tower ATX case. Nice and roomy but lacks ports in case for wire management. I have some specific options I'm looking for. They are as follows: mid/full tower, clear sided, 1 or 2 bays for 3.5" that are at the middle or...
PC Custom Builds and Overclocking
Which case is better?
Well, I'm gunna be building a computer for the first time (as seen in my last thread here). I was carefully comparing some parts (and still kinda am), and found a few other cases cheaper (except the last, but because it has 8 fans), and also looks like some could be better functionality-wise,...
PC Custom Builds and Overclocking
New case?
not sure if you can help me but i have a Fujitsu Esprimo E5905 Desktop with a Fujitsu D2164 and the original case can only hold 1 hdd and 1 dvd drive i want at least 2 preferably 3 hdd's and 2 dvd drives can any one help me with what case i can get? :D:devil:
PC Custom Builds and Overclocking

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 20:15.
Twitter Facebook Google+