Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.

Windows 7: ASROCK n68c-gsfx FX6300 overlock

24 Feb 2017   #1

Windows 7 Ultimate x64
ASROCK n68c-gsfx FX6300 overlock

HELLO to everyone!
i tried to overclock FX6300 from 3.5Ghz to 4.0-4.4,but everytime i try to run Prime95 to stress,everything froze or WIn10 "BSOD" and restart,i only play around with multiplier,on this PC i have asrock n68c-gsfx(i know it's not very good for OC) i wrote everything i found on OC Tweaker,i want to know what exactly turn on or off or disable!?i know that MB is a s**t for OC,but i only want to give a try!i found on a form a guy who OC his CPU to stable 4.1,but the thread is too old and i don't received any answers,message,or mail,and i waited 20 days!!

overclock mode [auto]
cpu frequency (mhz) [200]
PICE frequency (mhz) [100]
Boot failure guard [enabled]
boot failure guard count [3]
cpu/ldt spread spectrum [enabled]
PCIE spread spectrum [enabled]
sata spread spectrum [enabled]
CPU active core control [all cores]
AMD turbo core technology [auto]
AMD C-state support [enabled]
AMD APM [enabled]
processor maximum frequency x31.5 6300mhz
north bridge maximum frequency x31.0 6200mhz
processor maximum voltage 1.5500 V
Multiplier/voltage change [auto]
HT bus speed [auto]
HT bus width [auto]
memory configuration
memory clock [auto]
dram voltage [auto]
chipset settings
chipset voltage [auto]

what i need to turn on and off,enable or disable?thanks!!

My System SpecsSystem Spec
24 Feb 2017   #2
Mellon Head

Win 7 Pro x64/Win 10 Pro x64 dual boot

4.4 is a very aggressive overclock for that chip. I suggest that you turn down your expectations a little bit.

Before you start overclocking ask yourself a few questions:

1. What do I hope to achieve? More performance or bragging rights?
2. Is my cooling adequate? (a stock cooler will not cut it)
3. Can I afford to replace the CPU or motherboard if I overdo it and blow them up? (it's easy to do)
4. How good is my power supply?

If you don't know what BIOS settings to enable and disable to do this, I don't think that you're ready yet. I don't think you've done enough research. The best advice I can give is to answer yourself those four questions and do some serious research about your chip and motherboard. Also research basic overclocking techniques and concepts. It's very easy to destroy, or permanently damage your system when OCing. I would hate to give you advice and then have you bork your system because you didn't have a full understanding of what you were doing.

Baby steps, man. Baby steps.
My System SpecsSystem Spec
24 Feb 2017   #3

Win7 pro x64

ditto everything Mellon said. Also

1) Read this (the whole thing)

2) Post again here..
AMD - General

3) wait, I see you did post there. Recommend you read this. No offense intended.

AMD Overclock Guide for newbs!
My System SpecsSystem Spec


 ASROCK n68c-gsfx FX6300 overlock

Thread Tools

Similar help and support threads
Thread Forum
Will an AMD FX-6300 work with an AsRock N68C-GS FX
Hi All, As the title says, will an AMD FX-6300 processor work with an ASRock > N68C-GS FX motherboard? I'm planning to upgrade my system due to FPS drops whilst playing DOTA 2. I've concluded that since the FPS drops happen after several minutes while playing and seem to have nothing to do...
Hardware & Devices
ASRock N68C-GS FX Network controller driver
Hi folks, I have fresh installatioin of Windows 7 Ultimate SP 1 x32 edition running on my PC. When I go to Device Manager I see that my Network Controller drivers are not properly installed. My network card is also listed as beeing Nvidia nForce Network Controller which is incorrect. After...
ASRock A75 Pro4-M or Asrock B75 Pro3-M?
I used the A75 Pro4-M in my current build, but I'm building another for a friend. I'm not sure if I should go with the same board, or use the B75 Pro3-M this time. It's hard to find any reviews on either of these boards. I like the PCIE spacing on the A75 board, but I'd also like to try the...
Hardware & Devices
Restart issues with new motherboard Asrock N68C-S UCC
Hey guys, I am new to the forum, just signed up. To start things off I wanna ask if any of you have any experience with the Asrock N68C-S UCC motherboard or ever had to deal with a restart issue I'm facing with the Asrock N68C-S UCC. I just did a clean install after replacing my old ASUS...
Hardware & Devices
How can I overlock my Graphics Card?
I am very new to overclocking but would like to try and overclock my ATI Radeon X1200 Series Graphics Card. How can I go about doing this.
PC Custom Builds and Overclocking

Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 09:19.
Twitter Facebook