[Project] CM Haf 932 Paint Job and Wiring

Page 4 of 4 FirstFirst ... 234

  1. Posts : 6,885
    Windows 7 Ultimate x64, Mint 9
    Thread Starter
       #31

    Rattler1 said:
    Hello All,

    Please forgive my ignorance. I just the HAF 932 and am having problems simply identifying where the H.D.D LED and other USB wires go on my motherboard. Can anyone please assist?
    Your manual is THE best place to check (as said).

    My manual not only has pictures of how they fit, but came with a little pin thing with clearly labeled locations.

    Worst case scenario, just plug things in till it works (I have successfully used this method, but it took a while).

    ~Lordbob
      My Computer


  2. Posts : 296
    Windows 7 Professional
       #32

    Nice job!

    When is the HAF-X coming out, I've seen the review of the HAF-X from 3DGameMan and was drooling the whole time.

    Too bad I've just ordered the CM 690 II, the HAF 932 was my second choice and the HAF-X is the case of my dreams.

      My Computer


  3. Posts : 6,885
    Windows 7 Ultimate x64, Mint 9
    Thread Starter
       #33

    Nemix77 said:
    Nice job!

    When is the HAF-X coming out, I've seen the review of the HAF-X from 3DGameMan and was drooling the whole time.

    Too bad I've just ordered the CM 690 II, the HAF 932 was my second choice and the HAF-X is the case of my dreams.

    Haf-X looks pretty badass, but it won't quite measure up to what my 932 will look like in a few days!

    I just finished fixing the switch plate yesterday, so today I am going to polish it up. By that I mean that I will sand down the pounds of JB Weld I used and make it nice and smooth. Then I will work on getting everything mounted and wired up.

    ~Lordbob
      My Computer


  4. Posts : 296
    Windows 7 Professional
       #34

    Looking forward to see pics of the finished product, keep us updated.

    P.S. I like the Zalman ram-sink idea on your heat spreaders. I was thinking of doing that too but not sure if they'd fit, because I can only use memory dimms 3 and 4 due to the Mugen 2.

      My Computer


  5. Posts : 6,885
    Windows 7 Ultimate x64, Mint 9
    Thread Starter
       #35

    Nemix77 said:
    Looking forward to see pics of the finished product, keep us updated.

    P.S. I like the Zalman ram-sink idea on your heat spreaders. I was thinking of doing that too but not sure if they'd fit, because I can only use memory dimms 3 and 4 due to the Mugen 2.

    The ones I have?

    I got them for like $5 at Frys.

    ~Lordbob
      My Computer


  6. Posts : 6,885
    Windows 7 Ultimate x64, Mint 9
    Thread Starter
       #36

    Here is the update for my almost complete switch plate:
    [Project] CM Haf 932 Paint Job and Wiring-switchplateback.jpg
    [Project] CM Haf 932 Paint Job and Wiring-switchplatefront.jpg

    And yes, it DOES fit this time!

    ~Lordbob
      My Computer


  7. Posts : 6,885
    Windows 7 Ultimate x64, Mint 9
    Thread Starter
       #37

    And yet more updates!
    [Project] CM Haf 932 Paint Job and Wiring-2010-06-15-19.20.46_phoenix_arizona_us.jpg
    [Project] CM Haf 932 Paint Job and Wiring-plugged-plate.jpg

    I have set it up for painting now, so I will finish that tonight and let it dry for 24h.

    Now, onto those pots!

    ~Lordbob
      My Computer


  8. Posts : 6,885
    Windows 7 Ultimate x64, Mint 9
    Thread Starter
       #38

    I am moving updates to this thread:
    https://www.sevenforums.com/overclock...ontroller.html

    I am also very close to being done!

    ~Lordbob
      My Computer


 
Page 4 of 4 FirstFirst ... 234

  Related Discussions
Our Sites
Site Links
About Us
Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd
All times are GMT -5. The time now is 04:31.
Find Us