Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Help

29 Jul 2010   #1
LonnieMac

Windows 7
 
 
Help

could someone please check over my BIO settings please. I'm unable to flash it for some reason so I've had to do it manually but I'm not sure whether all is correct, the systems currently running at 2.19 GHz...

MSI KT400 board - AMD 3000+ XP Barton processor - 2.5GB RAM...


CMOS FEAT

Time/Date and hardware are set correctly

Boot sector virus protection - disabled



ADVANCED BIOS FEAT

Quick boot - enabled
full screen logo show - disabled
S.M.A.R.T H/D - disabled
Primary display - VGA/EGA
Internal cache - enabled
system BIO's cacheable - enabled
COOO, 32K shadow - cached
APIC funation - enabled
MPS Table Version - 1.4




ADVANCED CHIPSET FEAT

PCI delay transaction - disabled

DRAM TIMING CONTROL

host clock - 166
config sdram by - SPD
sdram freq - auto
sdram burst length - 4QW
sdram 1T command - disabled
fast command - fast
fast r-2-r turnaround - disabled

AGP

fast write - enabled
aperture size - 128mb
master write - disabled
master read - disabled
read synchronization - disabled




POWER MANAGEMENT

ipca - yes
acpi standby - S1/POS
apm - enabled
cpu critical temp - disabled
cpu HALT command detection - disabled




PNP/PCI CONFIGURATION

plug and play aware O/S - no
clear nvram - yes
pci latency timer - 32
pci ide bus master - disabled
primary graphics adapter - pci

PCI ~ SLOT 1 - 2/5 - 3/6 - 4 ---- AUTO





INTEGRATED PERIPHERALS

onchip IDE controller - both
onboard lan - enabled
onboard lan P.M.E - enabled
ac '97 audio - enabled
mc '97 modem - disabled
onchip USB controller - 6 USB PORTS
usb legacy support - no mice
port 64/60 emulation - disabled

(i'm using ethernet to connect to a modem)


PC HEALTH STATUS

chassis intrustion - disabled
cpu fan dection - enabled





FREQ/VOLTAGE CONTROL

spread spectrum - +0.25%
FSB 166

ratio - vcore - voltage - termination - agp ----- auto


My System SpecsSystem Spec
.
29 Jul 2010   #2
LonnieMac

Windows 7
 
 

I've had to change my FSB to 100 because I keep getting blue screen error... please help me ASAP.
My System SpecsSystem Spec
29 Jul 2010   #3
Tews

64-bit Windows 8.1 Pro
 
 

Exactly what problems are you having... it looks like you are overclocking too much.. return the values to their default settings...
My System SpecsSystem Spec
.

29 Jul 2010   #4
LonnieMac

Windows 7
 
 

default settings are strange, FSB is set at 100 and all my hardware gets disabled, lan, usb etc. all goes off.

Correct FSB should be set at 166 but when I change it, all i get is blue screen error.
My System SpecsSystem Spec
29 Jul 2010   #5
Tews

64-bit Windows 8.1 Pro
 
 

Follow these instructions and we'll see what we can do...

Blue Screen of Death (BSOD) Posting Instructions
My System SpecsSystem Spec
29 Jul 2010   #6
LonnieMac

Windows 7
 
 

does it matter that I've changed my FSB? correct 166 resulted in bluescreen but 100, which I've changed it too doesn't crash ? there no way of me running the scan with 166 set, it wont even boot and if it does, it will turn off.
My System SpecsSystem Spec
29 Jul 2010   #7
Tews

64-bit Windows 8.1 Pro
 
 

Please run the tool.. until you do there isnt a lot I can do... I need the .dmp files for analysis...
My System SpecsSystem Spec
29 Jul 2010   #8
LonnieMac

Windows 7
 
 

ok, its running now, should I create a new thread in the section or just post the zip file in here?
My System SpecsSystem Spec
29 Jul 2010   #9
Tews

64-bit Windows 8.1 Pro
 
 

You can post it here..
My System SpecsSystem Spec
29 Jul 2010   #10
LonnieMac

Windows 7
 
 

files attached, I couldn't do a System Health Report though,

Quote:
Error:

An error occured while attempting to generate the report.

The system cannot find the path specified.
edit: file removed, not needed.
My System SpecsSystem Spec
Reply

 Help




Thread Tools



Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 22:54.
Twitter Facebook Google+ Seven Forums iOS App Seven Forums Android App