Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Memory Issues

10 Sep 2009   #11
Dwarf

Windows 8.1 Pro RTM x64
 
 

Have a look at this from Intel.
Quote   Quote: Originally Posted by Intel
If you are using DDR3 1600 MHz DIMMs, it is recommended that you only populate two of the four DIMM slots, specifically one slot in each channel. It is recommended that you populate slot 1 of each channel (black connectors).
More... Intel® Desktop Board DX48BT2 - System memory


My System SpecsSystem Spec
.
10 Sep 2009   #12
zigzag3143

Win 8 Release candidate 8400
 
 

I do think both Brink and Dwarf are correct it seems most likely that it is the added (new ) memory but it can hurt to verify it.
My System SpecsSystem Spec
10 Sep 2009   #13
TGSoldier

 
 

Did you ever experience any blue screens with the "old memory" alone?

Did you run Memtest on the new memory ?
My System SpecsSystem Spec
.

10 Sep 2009   #14
drklazarus26

Windows 7 Ultimate x64 Retail
 
 

Quote   Quote: Originally Posted by Brink View Post
Are you sure that the new RAM sticks have the exact same voltage and timing settings as the older sticks?

Do these voltage and timing settings above match what is set in the BIOS for the memory?
i actually copy and pasted the previous memory order and yes i checked everything. oddly enough the chips in the dimm 1 slots are running differently. dimm 0 channel a & b are running 7-7-7-16 and dimm 1 a & b 7-7-7-20 and this is the case with all the chips. here is the dmp link MEGAUPLOAD - The leading online storage and file delivery service
My System SpecsSystem Spec
10 Sep 2009   #15
drklazarus26

Windows 7 Ultimate x64 Retail
 
 

i actually tested both sets seperately and they are good. as we speak i am using the newer ram and i removed the older ram to see if anything would happen. so far everything seems to be fine
My System SpecsSystem Spec
10 Sep 2009   #16
Dwarf

Windows 8.1 Pro RTM x64
 
 

If you swap the RAM chips over, i.e. place the RAM from dimm 0 channels a & b into dimm 1 channels a & b and vice-versa, do you get the same timing as above?
My System SpecsSystem Spec
10 Sep 2009   #17
drklazarus26

Windows 7 Ultimate x64 Retail
 
 

Quote   Quote: Originally Posted by Dwarf View Post
If you swap the RAM chips over, i.e. place the RAM from dimm 0 channels a & b into dimm 1 channels a & b and vice-versa, do you get the same timing as above?
yes. both chips have the same sticker on them. they say 7-7-7 @ 1.9v
My System SpecsSystem Spec
10 Sep 2009   #18
zigzag3143

Win 8 Release candidate 8400
 
 

Well You weren't kidding 99Meg dmp file. It took me 3 minuutes to open it. I dont have a true debugger to analyse this but Im posting the info for someone who does. It appears that ntkrnlmp.exe caused this and only part of it was trapped. that leads me back to the memory. the dump paged out of memory. While waiting for a guru debugger, I would see if I could sync the settings for the old memory and the new mem. Failing that try pulling the new set to see if you get bsod's, then pull the oldd just to narrow it down.

ken
Code:
 
Microsoft (R) Windows Debugger Version 6.11.0001.404 X86
Copyright (c) Microsoft Corporation. All rights reserved.
 
 
Loading Dump File [C:\Users\K\Desktop\MEMORY.DMP]
Kernel Summary Dump File: Only kernel address space is available
 
Symbol search path is: SRV*d:\symbols*Symbol information
Executable search path is: 
Windows 7 Kernel Version 7600 MP (4 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 7600.16385.amd64fre.win7_rtm.090713-1255
Machine Name:
Kernel base = 0xfffff800`02a4a000 PsLoadedModuleList = 0xfffff800`02c87e50
Debug session time: Wed Sep 9 16:12:45.968 2009 (GMT-4)
System Uptime: 0 days 1:35:49.578
Loading Kernel Symbols
...............................................................
................................................................
...............................
Loading User Symbols
PEB is paged out (Peb.Ldr = 000007ff`fffd8018). Type ".hh dbgerr001" for details
Loading unloaded module list
..........
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
 
Use !analyze -v to get detailed debugging information.
 
BugCheck 1E, {ffffffffc0000005, 0, 8, 0}
 
PEB is paged out (Peb.Ldr = 000007ff`fffd8018). Type ".hh dbgerr001" for details
PEB is paged out (Peb.Ldr = 000007ff`fffd8018). Type ".hh dbgerr001" for details
Probably caused by : ntkrnlmp.exe ( nt! ?? ::FNODOBFM::`string'+460da )
 
Followup: MachineOwner
---------
 
3: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
 
KMODE_EXCEPTION_NOT_HANDLED (1e)
This is a very common bugcheck. Usually the exception address pinpoints
the driver/function that caused the problem. Always note this address
as well as the link date of the driver/image that contains this address.
Arguments:
Arg1: ffffffffc0000005, The exception code that was not handled
Arg2: 0000000000000000, The address that the exception occurred at
Arg3: 0000000000000008, Parameter 0 of the exception
Arg4: 0000000000000000, Parameter 1 of the exception
 
Debugging Details:
------------------
 
PEB is paged out (Peb.Ldr = 000007ff`fffd8018). Type ".hh dbgerr001" for details
PEB is paged out (Peb.Ldr = 000007ff`fffd8018). Type ".hh dbgerr001" for details
 
EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.
 
FAULTING_IP: 
+5a99952f03b0d804
00000000`00000000 ?? ???
 
EXCEPTION_PARAMETER1: 0000000000000008
 
EXCEPTION_PARAMETER2: 0000000000000000
 
WRITE_ADDRESS: 0000000000000000 
 
DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
 
BUGCHECK_STR: 0x1E
 
PROCESS_NAME: csrss.exe
 
CURRENT_IRQL: 0
 
TRAP_FRAME: fffff8800822e7f0 -- (.trap 0xfffff8800822e7f0)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=00000000c000000d rbx=0000000000000000 rcx=fffff900c01154e8
rdx=fffffa8006314da0 rsi=0000000000000000 rdi=0000000000000000
rip=0000000000000000 rsp=fffff8800822e980 rbp=0000000000000000
r8=0000000000369ea1 r9=000000000000000c r10=0000000000000000
r11=fffff8800822e960 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0 nv up ei ng nz na pe nc
00000000`00000000 ?? ???
Resetting default scope
 
LAST_CONTROL_TRANSFER: from fffff80002afba17 to fffff80002abbf00
 
STACK_TEXT: 
fffff880`0822df68 fffff800`02afba17 : 00000000`0000001e ffffffff`c0000005 00000000`00000000 00000000`00000008 : nt!KeBugCheckEx
fffff880`0822df70 fffff800`02abb542 : fffff880`0822e748 00000000`00000000 fffff880`0822e7f0 00000000`00000000 : nt! ?? ::FNODOBFM::`string'+0x460da
fffff880`0822e610 fffff800`02aba0ba : 00000000`00000008 00000000`00000000 fffff880`0822e900 fffff900`c0120020 : nt!KiExceptionDispatch+0xc2
fffff880`0822e7f0 00000000`00000000 : 00000000`fffffc81 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiPageFault+0x23a
 
 
STACK_COMMAND: kb
 
FOLLOWUP_IP: 
nt! ?? ::FNODOBFM::`string'+460da
fffff800`02afba17 cc int 3
 
SYMBOL_STACK_INDEX: 1
 
SYMBOL_NAME: nt! ?? ::FNODOBFM::`string'+460da
 
FOLLOWUP_NAME: MachineOwner
 
MODULE_NAME: nt
 
IMAGE_NAME: ntkrnlmp.exe
 
DEBUG_FLR_IMAGE_TIMESTAMP: 4a5bc600
 
FAILURE_BUCKET_ID: X64_0x1E_nt!_??_::FNODOBFM::_string_+460da
 
BUCKET_ID: X64_0x1E_nt!_??_::FNODOBFM::_string_+460da
 
Followup: MachineOwner
My System SpecsSystem Spec
10 Sep 2009   #19
drklazarus26

Windows 7 Ultimate x64 Retail
 
 

Quote   Quote: Originally Posted by zigzag3143 View Post
I would see if I could sync the settings for the old memory and the new mem. Failing that try pulling the new set to see if you get bsod's, then pull the oldd just to narrow it down.
I tried syncing the settings. i matched them up to 7-7-7-16 and 7-7-7-20 and had no luck. right now i have the new chips in and everything is working fine and i also had the old chips is for a few days and still nothing
My System SpecsSystem Spec
10 Sep 2009   #20
Brink

64-bit Windows 10 Pro
 
 

Quote   Quote: Originally Posted by drklazarus26 View Post
Quote   Quote: Originally Posted by zigzag3143 View Post
I would see if I could sync the settings for the old memory and the new mem. Failing that try pulling the new set to see if you get bsod's, then pull the oldd just to narrow it down.
I tried syncing the settings. i matched them up to 7-7-7-16 and 7-7-7-20 and had no luck. right now i have the new chips in and everything is working fine and i also had the old chips is for a few days and still nothing
Do you have the option to set all 4 to the same timings in the BIOS?
My System SpecsSystem Spec
Reply

 Memory Issues




Thread Tools




Similar help and support threads
Thread Forum
Memory Issues on new Setup
First of all, thanks for taking your time to read this. A week ago, i transferred my HDD with the Windows 7 installation along with 8 GB of RAM and the PSU to a completely new motherboard. Since my download rate is only 240kb/ps, i didn't want to go through the trouble of re-downloading my whole...
Performance & Maintenance
New Memory Issues ??
About a week ago,I installed some new ram in a Presario CQ 57-229WM.I removed (1) one gb stick out of two and replaced it with a 4 gb stick for a total of five.Upon reboots my pc began giving me error messages such as a "hardware problem" within the memory and that my drive needed to be scanned for...
Hardware & Devices
Memory Issues on a CPU with 8GB RAM
Hi, I recently re-installed Windows 7 and would like to re-install Sony Vegas Pro 12. I did so and after editing some videos for around 5 minutes, I received a pop-up warning: Close programs to prevent information loss: Sony Vegas. I don't understand how having 8GB of RAM on an i7 2600k on a...
Performance & Maintenance
Memory issues on a DZ77GA-70K
I'm building my "new" system using an Intel DZ77GA-70K. In my previous system, I had Patriot Viper 3 memory (link below), in a 2x8 GB configuration. The board doesn't boot with both or just one of the memory chips installed. I get 3 short beeps, repeated once, then the system power cycles and does...
Hardware & Devices
BSODs & Memory Issues?
Hi all, First of all, I really think this forum is really awesome! Secondly, Im new here and im from Holland so excuse me for my bad english xD 2 weeks ago I bought some new parts for my computer: - Intel Core i7-950 - ASRock X58 Extrem3 mobo - OCZ 2x2GB DDR1066 - GeForce GTX 460 from...
BSOD Help and Support
Memory Issues?
Hi, I've had several crashes yesterday and today, and I'm a little stumped by them. It started while I was playing WoW, bluescreen out of nowhere. No file specifically mentioned, but the error was MEMORY_MANAGEMENT, first part of the error code was 0x0000001a. Shrugged it off, a one off...
BSOD Help and Support


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd

All times are GMT -5. The time now is 14:21.
Twitter Facebook Google+ Seven Forums iOS App Seven Forums Android App