Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: How to direct "line in" to both channels?

27 May 2010   #1
Vorak666

Windows 7
 
 
How to direct "line in" to both channels?

I luv playing guitar with playback, but now after upgrade to win7 I don't know how to direct the line in feed into both left and right channels... Result is while pc playback song is playing into both channels in my headset, I can only hear the realtime play (line in jack) at my left ear. Need to route the sound (which is mono, of course) into both and after google still dunno how. Ty for tips.


My System SpecsSystem Spec
.
27 May 2010   #2
maceman

 

Hi Vorak666,
Simple reason for that is that you're recording to stereo track. Your monitoring is probably mono (it often is) and you can hear it from both channels. The solution is that you use a mono track.
If that is not possible, you have to get stereo sound out from your guitar. a small mixer will make that trick.
My System SpecsSystem Spec
27 May 2010   #3
Zepher

Windows 7 Ultimate 64bit
 
 

all you need is a mono to stereo cable or adapters.
For only $0.66 each when QTY 50+ purchased - RCA Audio Splitter Adapter (3.5mm Male to 2 RCA Female) (Stereo) | RCA Adapters

Hosa Technology | Mono 1/4" Phone Male to 2 RCA | CYR-103

Tell us how and what cables you are running from your guitar to the PC.
My System SpecsSystem Spec
.

28 May 2010   #4
Vorak666

Windows 7
 
 

Ty for hints... But the problem isn't for recording anything. Realtime playback comes back trough only one channel. It isn't stereo, I know but I'd need to route the sound so that what ever is input either in line-in or microphone jacks (even if mono basic large plug with an adapter) is listenable realtime (without audio recording software of anykind being open) in left and right channels... Dunno if this seems a tall order but in XP it was given, straight up, no tricks... Oh, and I'm using the very same external (cables, pod, jacks) as before in XP....
Again either is fine, mic or line in... just gimme one
My System SpecsSystem Spec
Reply

 How to direct "line in" to both channels?




Thread Tools




Similar help and support threads
Thread Forum
No Boot, CHKDSK Fails: "Cannot Open Volume For Direct Access."
Hello, I am receiving this error upon boot: Cannot open volume for direct access. Autochk cannot run due to an error caused by a recently installed software package. Use the system restore feature from the control panel to restore the system to a point prior to the recent software package...
Hardware & Devices
On My Home Network: "Windows cannot access ...Documents" in one direct
Dear Forum, I am trying to set up a Home Network between two computers both running Windows 7 Pro 64-bit with SP1. I tried many suggestions but with no avail. The "LACI" computer used to work in a Workgroup (with a third computer) previously but now it doesn't work in the Home Network. Please see...
Network & Sharing
Run "cmd.exe" as a given user and "as administrator" in command line
Hello and thank you for reading my post. If I'm logged in Windows as user "u1", I can execute "cmd.exe" "as administrator" by choosing "Start" -> "cmd.exe" and right-click "Run as administrator".I would like to start another "cmd.exe" console as "u2" and "as administrator". (So, "u2" is not...
General Discussion
Direct X components "Not Available" / Arma II Display Adapter Error.
First, here is the basic information about my 2009 MacBook Pro: OS X 10.8.2 (12C60) Processor: 2.26 GHz Intel Core 2 Duo Memory: 4 GB 1067 MHz DDR3 Graphics: NVIDIA GeForce 9400M 256 MB -- I have used boot camp to create a Windows Partition on my Mac and have installed Windows 7. The main...
Gaming
Live TV: Channels tune ok, "No signal" trying to watch.
I have a strange problem with my W7MCE. I've googled for a long time but havent found an answer. I hope someone else has answer... I have 2x AnySee DVB-T tuners and 1x TechnoTrend T-1500 tuner. I can tune in channels fine, it finds all channels. My EPG updates without any problems. But...
Media Center


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 02:18.
Twitter Facebook Google+ Seven Forums iOS App Seven Forums Android App