Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: Lastwake Command

09 Jul 2015   #10
ColFrogfoot

Nova Scotia
 
 

Thats what I just tried I got this I said
Sleep Time: ‎2015‎-‎07‎-‎09T13:31:38.329965500Z
Wake Time: ‎2015‎-‎07‎-‎09T13:46:45.997946700Z

Wake Source: Unknown

Also I just noticed this is windows 7 forums, Im on windows 8 :/


My System SpecsSystem Spec
.
09 Jul 2015   #11
Brink

64-bit Windows 10 Pro
 
 

That's ok. This is the same in Windows 8 as well.

In that case, check to see what devices are allowed to wake the PC, and troubleshoot by disabling them one at a time from being able to wake up the PC and test to see if the PC still wakes up afterwards. Usually, it's the network adapter at fault.

Devices - See Devices that are able to Wake Up the Computer

Devices - Allow or Prevent to Wake Up Computer
My System SpecsSystem Spec
09 Jul 2015   #12
ColFrogfoot

Nova Scotia
 
 

powercfg -devicequery wake_armed

NONE

(Ive turned everything off previously)
My System SpecsSystem Spec
09 Jul 2015   #13
ColFrogfoot

Nova Scotia
 
 

Also I should note this is a new computer that I just got and its had this problem from the start. So I'm thinking it might be a manufacturing error? I dont know
My System SpecsSystem Spec
.

09 Jul 2015   #14
Brink

64-bit Windows 10 Pro
 
 

To troubleshoot, disconnect anything that you have connected to the PC and put it to sleep to see if it still wakes up. If not, connect each device one at a time testing in between to see if the PC wakes with it connected until hopefully a culprit is revealed.
My System SpecsSystem Spec
09 Jul 2015   #15
ColFrogfoot

Nova Scotia
 
 

Alright I will but excuse me for an hour I'm in class but I'll try that right as I get back
My System SpecsSystem Spec
09 Jul 2015   #16
Brink

64-bit Windows 10 Pro
 
 

Ok. I'll be here when ready. :)
My System SpecsSystem Spec
09 Jul 2015   #17
ColFrogfoot

Nova Scotia
 
 

Hey just posting an update. I unplugged everything and it didn't wake from sleep for about 40 minutes then I plugged everything in slowly over spans of about 20-30min and it wasn't waking still. So I turned it off and on again and soon after with everything plugged in it turned on again. So now I'll unplug one at a time again. This time I have classes for about 3 hours again but before I left for classes I unplugged the Ethernet cord because that's what I think might be the problem. So when I get back I'll see if it came off of sleep mode and let u know. By the way, thanks a lot for all this help
My System SpecsSystem Spec
09 Jul 2015   #18
Brink

64-bit Windows 10 Pro
 
 

Great news so far. Now it's just a process of elimination matter. :)
My System SpecsSystem Spec
09 Jul 2015   #19
ColFrogfoot

Nova Scotia
 
 

Hey so I got back from class and it was not on. So I'm going to be inclined to say right now that it is my Ethernet cord that is somehow causing the problem.
My System SpecsSystem Spec
Reply

 Lastwake Command




Thread Tools




Similar help and support threads
Thread Forum
Command Prompt command <ipconfig> not working
when I open up my command prompt and type 'ipconfig' without the ' and press enter it returns the line: 'ipconfig' is nto recognized as an internal or external command, operable program, or batch file I am trying to find out the information I need in order to set up a static IP Address for port...
Network & Sharing
Command Prompt: Repeat del command continuosly
Hi All, I'm running a program that parses .csv files and then changes them into ._OK files. This process takes longer when there are a large number of *.OK files in the folder where the files being converted are located. To remedy this I occasionally manually run this command: del *._OK ...
General Discussion
Executing command line command anywhere ?
I want to create a setup whereas a command line command can be run from any directory/folder, without having to be in the directory/folder whereas the command line command resides ?
General Discussion
"Copy" command in command prompt generates 0x1a artifact?
Hello Everybody! I don't know if this is a real issue, or just one of those "What the . . . .!!" situations. You judge. Situation: I was working on a batch file that combines two .txt (ASCII?) files created in Notepad to create a composite file, and I noticed something really interesting. ...
Software
My Windows 7 64bit Home Premium does not have a COMMAND or COM command
When I am told to go to START/SEARCH and type in COMMAND, so I can RUN as Admin, it finds neither COM.exe or COMMAND.exe so I can "Run as Admin" in the DOS windows. It use to. I do have a RUN command that will bring up the DOS window but when executing some commands like CHKDSK it tells me I...
General Discussion


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

© Designer Media Ltd

All times are GMT -5. The time now is 20:53.
Twitter Facebook Google+ Seven Forums iOS App Seven Forums Android App