Windows 7 Forums
Welcome to Windows 7 Forums. Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. We also provide an extensive Windows 7 tutorial section that covers a wide range of tips and tricks.


Windows 7: System Restore

12 Apr 2013   #100
mickeyg2008

windows 7
 
 

Did not restore says it failed while scanning the file system on the drive c:\
It is telling me to run chkdsc /r on this disc. Can you tell me how to do this please.
Error (0x80070571)
Thanks


My System SpecsSystem Spec
.
12 Apr 2013   #101
Brink

64-bit Windows 10 Pro
 
 

Mickey,

Option Two in the tutorial below can help show you how to run the command below. :)

chkdsc C: /r


Disk Check
My System SpecsSystem Spec
13 Apr 2013   #102
mickeyg2008

windows 7
 
 

Good morning. Restore was successful fixing a lot of errors but still have not been able to get the diagnostics policy service running. Can it comes up when i troubleshoot not being able to get an internet connection would you please tell me about that.thanks
My System SpecsSystem Spec
13 Apr 2013   #103
mickeyg2008

windows 7
 
 

I did the instructions here for making sure that the diagnostic policy service is on automatic and it is. It could not start it getting an error 5 /access denied. Thanks
My System SpecsSystem Spec
.

13 Apr 2013   #104
Brink

64-bit Windows 10 Pro
 
 

Mickey,

See if this may help to make sure the "Log On" settings for the Diagnostic Policy Service are still set properly for access.


1. Open the Services window,

2. Right-click the Diagnostic Policy Service service, and click on Properties.

3. Click the Log On tab, and then do one of the following:

4. To specify that the service uses the "Local Service" account, select (dot) This account, and then

5. Type NT AUTHORITY\LocalService in the "This account" field. Do not type a password. The password fields need to be empty.

6. Click on Apply button.

7. If prompted, click on OK for the "The new logon name will not take effect until you stop and restart the service" message.

8. Click on General tap, then see if you may be able to start the service. If it's already started not, then stop and start it.

9. Click OK to close properties, then close Services.
My System SpecsSystem Spec
13 Apr 2013   #105
mickeyg2008

windows 7
 
 

It is requesting a valid password.
My System SpecsSystem Spec
13 Apr 2013   #106
Brink

64-bit Windows 10 Pro
 
 

Did you select (dot) the This account option, and not the Local System account option?

If so, be sure to clear the password fields for "This account" after entering NT AUTHORITY\LocalService and clicking on Apply.
My System SpecsSystem Spec
13 Apr 2013   #107
mickeyg2008

windows 7
 
 

I did. Hey..thanks for all this help!! I followed the instructions and restarted no change. I opened my internet connection. I have a limited access. It says that. The dependency service failed to start. Can we do anything with that..??
My System SpecsSystem Spec
13 Apr 2013   #108
mickeyg2008

windows 7
 
 

OK..I quit spinning. What do I do next. ??
My System SpecsSystem Spec
13 Apr 2013   #109
Brink

64-bit Windows 10 Pro
 
 

If the service's "Log on" settings are set properly now, then are you able to run the chkdsk /r command now?
My System SpecsSystem Spec
Reply

 System Restore




Thread Tools




Similar help and support threads
Thread Forum
System restore didn't work. I have all system restore points
Hi. I'm using 500GB hdd(source) and 500GB ssd(destination) and I've some questions: 1. I Did 1:1 copy of disc (in norton GHOST) and on destination disk system restore is telling that i don't have restore points. Why? 2. Then On source disc I was trying to unlock some disc space by entering System...
Backup and Restore
Windows 7 - System Restore, Saving a Backup & Permanant Restore Point
My questions are on Windows 7 System Restore, Restore Points and Backups; specifically, potentially using a Backup as a Permanent Restore Point. Here is the situation... About a month ago, I did a complete Factory Restore on my HP desktop and returned it to it's factory condition. After...
Backup and Restore
System Restore isn't creating (or saving?) restore points properly
For some reason my System Restore function isn't automatically creating (or isn't showing) System Restore points as it should be doing for "major" system events (e.g., isn't automatically creating restore points before/after Windows Updates and software/driver updates). I'm not sure if it isn't...
Backup and Restore
Allocated System Restore space holds far fewer restore points now
I have 8gb of space allocated to System Restore, all monitoring my C partition only. This space is always at least 85-90% used according to the System Protection screen. In the past I have had at least 15 restore points to choose from after ticking "show more restore points." But today I went to...
Backup and Restore
System Restore - Restore system settings and previous versions of file
estore system settings and previous versions of file is greyed out on my system, I may have disabled a required service for this, can anyone point me to the right direction for this? As I'm about to try the X-Fi MB2 mod again as the last time I tried it my system was messed up that it wont even...
Backup and Restore


Our Sites

Site Links

About Us

Find Us

Windows 7 Forums is an independent web site and has not been authorized, sponsored, or otherwise approved by Microsoft Corporation. "Windows 7" and related materials are trademarks of Microsoft Corp.

Designer Media Ltd

All times are GMT -5. The time now is 07:13.
Twitter Facebook Google+