BSOD non - stop comp rebooting and beeps after and comp freezes

[rutark100]

i have win 7 ultimate x64
my comp won't stop BSOD and mentions ntoskrnl.exe+80640 as the main cause for this, the pc also freezes repeatedly, also recently it started rebootin and beeping after that.
can't find the solution im strugglin from that more than a month
the bios also behaves wierdly lately, it changed it self time and system time and also changed RAM frequency.
after turning driver verifier my comp reboot more frequently
i hope some1 can help me get to solution becauze im really lost, i added all the files required for you to help me.
thanx , mark

 

[axe0]

Hi Mark,

Welcome to the 7forums.

Please re-run the tool, there are some important files missing.

 

[rutark100]

hey axeo thanx alot
here's another try, which is done while driver verifier test
sry for late response hard to do anything between boots and freezes

 

[axe0]

Please keep in mind that this section of the sevenforums.com is ONLY for BSOD crashes, I likely won't be able to help you properly with the sudden reboots.

The zip still doesn't contain all of the files, but it is an improvement.

The crashes are all over the place, this usually means a lower level problem with the system and usually have some causes like

• malware infection
• software compatibility problems
• missing windows updates
• BIOS problems

Please visit Windows Update and install every update available, it may take a couple of times to get them all.

Please uninstall everything of AMD using Display Driver Uninstaller and install new drivers from AMD

*** WARNING: Unable to verify timestamp for atikmdag.sys
*** ERROR: Module load completed but symbols could not be loaded for atikmdag.sys

Please check every installed 3rd party program for updates, like Malwarebytes

3: kd> lmvm mbamchameleon
start             end                 module name
fffff880`0157f000 fffff880`01599000   mbamchameleon T (no symbols)           
    Loaded symbol image file: mbamchameleon.sys
    Image path: \??\C:\Windows\system32\drivers\mbamchameleon.sys
    Image name: mbamchameleon.sys
    Timestamp:        [COLOR="Red"]Mon Aug 18 16:53:30 2014[/COLOR] (53F2136A)
    CheckSum:         0001C8F7
    ImageSize:        0001A000
    Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4

Please try following:

• Open an admin command prompt
• Copy/paste "sfc/scannow" (without quotes) and press enter
• When it finished reboot your system
• Open again an admin command prompt
• Enter sfc/scannow again

If sfc/scannow does NOT say "Windows Resource Protection did not find any integrity violation", please upload the cbs.log file located at {windows partition}\Windows\Logs\CBS\, if the file is too large try a 3rd party uploader like dropbox, onedrive, google drive, mediafire etc.
System File Check(SFC a.k.a. Windows Resource Protection) needs to have your system rebooted in order for sfc to try to fix the problems that it finds.

As there is a 0x50(PAGE_FAULT_IN_NONPAGED_AREA) and 0xD1(DRIVER_IRQL_NOT_LESS_OR_EQUAL) with both read errors and a 0x1A(MEMORY_MANAGEMENT) please test your memory using MemTest86+

Diagnostic Test

 RAM TEST

Run MemTest86+ to analyse your RAM. MemTest86+ - Test RAM - Windows 7 Forums

   Note

MemTest86+ needs to be run for at least 8 passes for conclusive results. Set it running before you go to bed and leave it overnight. We're looking for zero errors here. Even a single error will indicate RAM failure.

PAGE_FAULT_IN_NONPAGED_AREA (50)
Invalid system memory was referenced.  This cannot be protected by try-except,
it must be protected by a Probe.  Typically the address is just plain bad or it
is pointing at freed memory.
Arguments:
Arg1: [COLOR="Red"]fffff900c6543e06, memory referenced[/COLOR].
Arg2: [COLOR="red"]0000000000000000[/COLOR], [COLOR="red"]value 0 = read operation[/COLOR], 1 = write operation.
Arg3: fffff960001a9c70, If non-zero, the instruction address which referenced the bad memory
	address.
Arg4: 0000000000000002, (reserved)