BSOD playing FIFA 15

[essenbe]

Please Run Memtest86+

   Information

Please download from this site only http://www.memtest.org/ in the middle of the page are the Download links, you can download the ISO.zip or the Auto USB Flash Drive installer.zip

Extract the Zip file. If you chose the ISO image, burn it to a CD using Windows Disk Image Burner or any Image burner you may have. If you downloaded the Auto USB installer, extract it, insert your USB 2.0 Flash Drive and take note of the drive letter. Run the installer, select the Flash Drive Letter, check the format box and press next. It will install memtest86+ to a flash drive. You can use either V4.20 or V5.01. Boot from your selected media. If you use V5.01 it will tell you to press certain buttons at the start, please press no buttons. The test will begin on it's own and continue to run until you stop it. It needs to run for 8 complete passes or until you receive an error. If you receive an error, stop the test. Even 1 error is a fail. Each pass tests a different part of the ram and each of the 10 tests in each pass tests something different. It takes a minimum of 8 passes to completely test the ram, more passes are better. It is quite a long test and will take several hours depending on how much ram you have. Due to the time length it is best to run overnight. If you have any questions, please do not hesitate to ask​

 

[Casual]

Ok, I will test it not today, but will try it tomorrow maybe. I have tested RAM a few months ago and everything was good, maybe now it will find something.

 

[Casual]

Btw. Should I update BIOS gradually or to newest version?

 

[essenbe]

I always just update to the newest. Just make sure you are stable enough. If you BSOD during a bios update, you can brick the whole motherboard. Be sure to know what your Sata controller is set to. After the bios update, set the bios to optimized defaults, set the sata controller to what it is right now (or you won't boot). set your ram timings, frequency and Dram Voltage to what it is now, set your boot priority, save and exit.

 

[Casual]

Ok, will try it.

 

[Casual]

So yeah, i update BIOS it boot normally but I still get blue screens or "AMD driver has stopped working..." or even my comptuer is turing off automatically. I havent test my RAM still I will try test it today.

 

[essenbe]

Go into BIOS and tell me the Values for your +12V, +5V and +3.3V. Do you have another graphics card or someone who will help you and switch cards with you? That is the best test. Also post The BSOD posting instructions again http://www.sevenforums.com/bsod-help-support/96879-blue-screen-death-bsod-posting-instructions.html

Did you build the computer yourself?

 

[Casual]

I have old X300SE graphic card and i dont know how its possible but i didnt get new minidump file. Yes i build it by myself. After restar i will tell you the V.

 

[essenbe]

OK, no problem. I would like you to use a more modern card that pulls as much voltage as your current card, if anyway possible, other than buying one.

If it isn't your ram, it is most likely the Card, PSU or the motherboard. Do you have an extra empty Hard drive you can use? I would also ask that you do nothing else on your own. Let me guide you. Your BIOS updates were not failures. You just had your sata controller set on a different setting which kept you from booting.

When you installed the Motherboard did you have any extra standoffs? There should be a standoff for each hole in the motherboard to screw it down, no extras. There should be the ones that line up with the holes in the Motherboard and no more. is that the way it was, or were there extras?

 

[Casual]

I dont have any modern card than my own HD6750. No i dont own extra HDD my current WD was new but i installed Windows instantly that he arrived. No i didnt have any extras standoff.
Here is my voltage.
Vcore 1.408V sometimes its 1.416V
+3.30V 3.360V
+5.00V 5.088V
+12.00V 12.144V sometimes its 12.091V

 

[essenbe]

Can you borrow a card from a friend? Use his card in your computer and your card in his computer? That is the best way to test if the card is bad or if you have other problems.

Please run Memtest and follow the instructions below. If you don't understand or have questions, please ask.

Please Run Memtest86+

   Information

Please download from this site only http://www.memtest.org/ in the middle of the page are the Download links, you can download the ISO.zip or the Auto USB Flash Drive installer.zip

Extract the Zip file. If you chose the ISO image, burn it to a CD using Windows Disk Image Burner or any Image burner you may have. If you downloaded the Auto USB installer, extract it, insert your USB 2.0 Flash Drive and take note of the drive letter. Run the installer, select the Flash Drive Letter, check the format box and press next. It will install memtest86+ to a flash drive. You can use either V4.20 or V5.01. Boot from your selected media. If you use V5.01 it will tell you to press certain buttons at the start, please press no buttons. The test will begin on it's own and continue to run until you stop it. It needs to run for 8 complete passes or until you receive an error. If you receive an error, stop the test. Even 1 error is a fail. Each pass tests a different part of the ram and each of the 10 tests in each pass tests something different. It takes a minimum of 8 passes to completely test the ram, more passes are better. It is quite a long test and will take several hours depending on how much ram you have. Due to the time length it is best to run overnight. If you have any questions, please do not hesitate to ask​

 

[Casual]

So... I've tested my RAM, and 0 errors.

 

[essenbe]

Make sure you have a good temp monitoring program for your Graphics card and run Furmark. http://www.sevenforums.com/tutorials/100356-video-card-stress-test-furmark.html But don't use Speedfan.

 

[Casual]

Ok, will try it, and will tell you how it works.

 

[Casual]

I have question about speedfan? I have to turn it off completely? Or should I just change to low RPM's?

 

[essenbe]

Did you read the last part of my post? Don't use Speedfan. Use something else. If you don't have a GPU temp program, try MSI Afterburner MSI Afterburner

 

[Casual]

So... I've tested and:
Stress 77 degrees C (with auto speed fan)
Normal 40 degrees C
And nothing happend.

 

[Casual]

Btw. In MSI it says temp is 77, in FurMark its 67.

 

[essenbe]

The temps are fine. Try reinstalling the graphics driver, this will tell you how.

I am going to give you some links that will help you get a good clean install and not have any drivers you don't need that will conflict with other drivers. Download a WHQL driver from http://www.sevenforums.com/graphic-cards/329659-latest-amd-catalyst-video-driver-windows-7-a.html . Once you have them downloaded, uninstall you current driver from control panel. next clean up any left over drivers from following this tutorial http://www.sevenforums.com/tutorials/83814-drivers-clean-left-over-files-after-uninstalling.html and select only ATI Display Drivers. After you have done that and rebooted, install the new driver, only select custom install and install only what you have to. Very few people need most of what they include. You do not need the audio/HDMI drivers as you already have that in your Motherboard drivers. Unless there is some reason you need them, the only thing you really need is the Display Driver.

 

[Casual]

Ok, will try it. Its obvious but i want to be sure. I dont have any TV's etc. So i dont have to download and install this HDMI thing, right?