Solved BSOD with wdf0100.sys

[trimark]

Walked in today with a BSOD. Has a page fault in wdf0100.sys. I have restarted a couple of times, either in safe mode or safe mode with networking, and sometimes it would restart by itself, sometimes it would give the same BSOD. A quick hardware check and nothing seems amiss. This computer is my shipping computer, so not much else on it but Worldship. I attached the dump file, please let me know what I can do

 

[BorisTheAnimal]

Hi trimark and welcome to sevenforums, I hope you'll enjoy your stay here!

I noticed that you haven't uploaded a zip, could you please follow http://www.sevenforums.com/bsod-help-support/96879-blue-screen-death-bsod-posting-instructions.html and upload a zip report here.

Could you please upload it because without it it will be next to impossible to help with your issue!

Cheers!
Boris

 

[trimark]

Sorry...

Sorry guys, I really thought i did that. Here it is.

 

[BorisTheAnimal]

Asch, no need to apologize.

Thanks for posting I'm researching your problems!

 

[axe0]

Please follow suggestions below carefully.

Diagnostics Test

 System File Check

Please try following:

• Open an admin command prompt
• Copy/paste "sfc/scannow" (without quotes) and press enter
• When it finished reboot your system
• Open again an admin command prompt
• Enter sfc/scannow again

If sfc/scannow does NOT say "Windows Resource Protection did not find any integrity violation", please upload the cbs.log file located at {windows partition}\Windows\Logs\CBS\, if the file is too large try a 3rd party uploader like dropbox, onedrive, google drive, mediafire etc.
System File Check(SFC a.k.a. Windows Resource Protection) needs to have your system rebooted in order for sfc to try to fix the problems that it finds.

Diagnostic Test

 RAM TEST

Run MemTest86+ to analyse your RAM. MemTest86+ - Test RAM - Windows 7 Forums

   Note

MemTest86+ needs to be run for at least 8 passes for conclusive results. Set it running before you go to bed and leave it overnight. We're looking for zero errors here. Even a single error will indicate RAM failure.

Diagnostics Test

 HDD TEST

Run SeaTools to check the integrity of your HDD. SeaTools for DOS and Windows - How to Use - Windows 7 Help Forums

   Note

Do not run SeaTools on an SSD as the results will be invalid.

Run chkdsk
Disk Check - Windows 7 Help Forums

Run HDTune to

• scan for errors, no quick scan but full scan
• check the health,
• benchmark.

It may take some time, but please take the time you need to perform it properly.
Let me know what the results are

• of the error scan,
• make a screenshot of the health of every hard drive and post the screenshots,
• post screenshots with the benchmark of the
  • transfer rate,
  • access time,
  • burst rate,
  • cpu usage.

Please fill in your system specs

Please follow this tutorial and download the tool. The tool will give you detailed information about your system specs, please fill in your system specs more completely.
How to fill in your system specs:

Please check your motherboard manufacturer for driver updates for the Nvidia Sata controller driver.
Driver Reference Table - nvstor.sys

fffff880`0326d740  fffff880`00e1343c*** WARNING: Unable to verify timestamp for nvstor.sys
*** ERROR: Module load completed but symbols could not be loaded for nvstor.sys
 nvstor+0x1343c
kd> lmvm nvstor
start             end                 module name
fffff880`00e00000 fffff880`00e2b000   nvstor   T (no symbols)           
    Loaded symbol image file: nvstor.sys
    Image path: \SystemRoot\system32\drivers\nvstor.sys
    Image name: nvstor.sys
    Timestamp:        [COLOR="Red"]Fri Mar 19 21:45:11 2010[/COLOR] (4BA3E257)
    CheckSum:         0002FE37
    ImageSize:        0002B000
    Translations:     0000.04b0 0000.04e4 0409.04b0 0409.04e4

 

[trimark]

So using the Memtest86, the memory tested ok for 8 times, then the next time I tried it after an hour of the computer being unplugged and ran it 8 more times, and it didn't pass, so i replaced it. So far so good.

Thanks for help everyone.