Hi all , firstly i'd like to say this forum is the BEST it has helped me out on more than a few occasions! Secondly a little background , i am a junior IT tech so can build pcs etc but a lot of the command prompt stuff goes over my head!
Here's what i wanted to do - have windows 7 ultimate installed in a protected environment for testing software etc without having another pc or risking my current data and install.
My HDD is 1 TB , made up of 4 partitons C: 200gb with 127 free , D: 365gb with 166 free , E: 365gb with 223 free and Z: system reserved 100 mb.
So i considered VM ware and virtual pc to test things but ideally I want to use all my system resources as i do a lot with video editing etc so came across this tutorial.
All went fine until the create vdisk command , i went for 40960 mb as per your tut and got this message - diskpart has encountered an eror. There is not enough space on the disk. See the system event log for more information. I tried with 1024 mb to test and got the same error. I then tried with the same command but with E: instead of C: and it carried on to create the VHD and completed the windows installation which then updated etc. All good i thought.
Restarted the PC to go to my default OS no problem went to advanced system properties and changed the default OS to original as it was set to the VHD and changed the time down to 10 seconds instead of 30.
Restarted again but now it will only boot to my original OS whichever boot selection i make! even more strange is that the VHD image is on a folder in D: drive! As above this was installed to E:! in the VHD folder I can see all the windows os files but cant get it to boot.
Sorry for the long winded post and any help is much appreciated.
Here's what i wanted to do - have windows 7 ultimate installed in a protected environment for testing software etc without having another pc or risking my current data and install.
My HDD is 1 TB , made up of 4 partitons C: 200gb with 127 free , D: 365gb with 166 free , E: 365gb with 223 free and Z: system reserved 100 mb.
So i considered VM ware and virtual pc to test things but ideally I want to use all my system resources as i do a lot with video editing etc so came across this tutorial.
All went fine until the create vdisk command , i went for 40960 mb as per your tut and got this message - diskpart has encountered an eror. There is not enough space on the disk. See the system event log for more information. I tried with 1024 mb to test and got the same error. I then tried with the same command but with E: instead of C: and it carried on to create the VHD and completed the windows installation which then updated etc. All good i thought.
Restarted the PC to go to my default OS no problem went to advanced system properties and changed the default OS to original as it was set to the VHD and changed the time down to 10 seconds instead of 30.
Restarted again but now it will only boot to my original OS whichever boot selection i make! even more strange is that the VHD image is on a folder in D: drive! As above this was installed to E:! in the VHD folder I can see all the windows os files but cant get it to boot.
Sorry for the long winded post and any help is much appreciated.
Last edited by a moderator:
My Computer
- OS
- Windows 7 x64
- CPU
- Intel Q9400
- Motherboard
- Asrock P43DE3
- Memory
- 6 GB Corsair XMS 3
- Graphics Card(s)
- Nvidia GT220
- Sound Card
- Generic 5.1
- Monitor(s) Displays
- 19" Viewsonic & 40" Sony Bravia
- Hard Drives
- 1TB WD Caviar
250 GB WD Caviar
320 GB Maxtor ( External)
- PSU
- Generic 750 w
- Case
- EZCool N530
- Cooling
- Air - 4 Akasa 8mm