New install SYSTEM_SERVICE_EXCEPTION STOP error 1e

[acw]

This is a new blade running Windows Server 2008 R2 SP1, did memory check did sfc /scannow no errors, and ran chkdisk /r no errors were found. This appears to happen regularly. Have been trying to track this down. Attached is the upload of the crash file. Appreciate any help.

 

[writhziden]

Problematic Software:

Start Menu\Programs\Diskeeper Corporation	Public:Start Menu\Programs\Diskeeper Corporation	Public

Diskeeper can cause crashes on some systems, so I would recommend removing it to test.



Security Software: ??? I recommend the following:

• Download and install Malwarebytes, update it, do not start the free trial, and then run a full scan. Also run a full scan with your antivirus software installed on your system. If you do not have antivirus software installed, see the http://www.sevenforums.com/system-s...-system-security-combination.html#post1732627 for better security steps and scanning tools. Make sure to update the security software before running the full scan with it.

The driver to blame for your most recent crashes is a Broadcom NetXtreme driver. Recommend re-installing. bxnd60a.sys


To fully re-install a driver, use the following steps.

1. First, download the latest driver. Then do the next steps.
2. Click Start Menu
3. Right Click My Computer/Computer
4. Click Manage
5. Click Device Manager from the list on the left
6. Find the device you are trying to uninstall by expanding the appropriate set of devices
7. Right click the device
8. Click Uninstall (do not click OK in the dialog box that pops up after hitting Uninstall)
9. Put a tick in Delete driver software for this device (if this option is available, otherwise just hit OK) and hit OK
10. Restart your computer only if Windows asks you to.
11. Install the latest driver for the device.

Alternatively:

1. Login as an adminstrative user.
2. First, download the latest driver. Then do the next steps.
3. Click Start Menu
4. Click Control Panel
5. Click Hardware and Sound
6. Click Device Manager (the last link under Devices and Printers)
7. Find the device you are trying to uninstall by expanding the appropriate set of devices
8. Right click the device
9. Click Uninstall (do not click OK in the dialog box that pops up after hitting Uninstall)
10. Put a tick in Delete driver software for this device (if this option is available, otherwise just hit OK) and hit OK
11. Restart your computer only if Windows asks you to.
12. Install the latest driver for the device.

 

[acw]

Still having stop errors...

Removed Diskeeper and updated the Broadcom drivers, and received two more stop errors. I have uploaded another set of crash dumps to see if we can get any more information. In the meantime I will update the Firmware of the broadcom device.

Let me know what is found.

Thank you very much!

Adam

 

[writhziden]

Crashes indicate hard disk problems and network related problems. This could mean hard disk corruption, bad sectors, a failing hard disk, Windows files or registry corruption, viruses, or memory problems.

• If you are overclocking any hardware, please stop.
  
  
• Run Disk Check with both boxes checked for all HDDs and with Automatically fix file system errors checked for all SSDs. Post back your logs for the checks after finding them using http://www.sevenforums.com/tutorials/96938-check-disk-chkdsk-read-event-viewer-log.html (you may need to search for wininit instead of chkdsk).
  For any drives that do not give the message:
  Windows has checked the file system and found no problems
  run disk check again as above. In other words, if it says:
  Windows has made corrections to the file system
  after running the disk check, run the disk check again.
  
  
• Run the short and long tests with SeaTools for HDDs.
  SeaTools for Windows
  
  SeaTools for DOS​
  
  
• If you have an SSD, make sure the following are up to date:
  • SSD firmware
  • BIOS Version
  • Chipset Drivers
  • Hard disk controller drivers/SATA drivers
  • If you have a Marvell IDE ATA/ATAPI device, uninstall it in device manager and see if the system performs better.
  
  
• Check Windows for corruption. Run http://www.sevenforums.com/tutorials/1538-sfc-scannow-command-system-file-checker.html up to three times to fix all errors with a restart in between each. Post back if it continues to show errors after a fourth run or if the first run comes back with no integrity violations. Use OPTION THREE of http://www.sevenforums.com/tutorials/1538-sfc-scannow-command-system-file-checker.html to provide us with the sfcdetails.txt file if errors occur.
  
  
• Download and install Malwarebytes, update it, do not start the free trial, and then run a full scan. Also run a full scan with your antivirus software installed on your system. If you do not have antivirus software installed, see the http://www.sevenforums.com/system-s...-system-security-combination.html#post1732627 for better security steps and scanning tools. Make sure to update the security software before running the full scan.
  
  
• Run the boot version of Memtest86+ paying close attention to Parts 2 and 3 of the tutorial. Also, in case Memtest86+ misses anything and comes up with no errors, run the extended version of the Windows Memory Diagnostics Tool for at least five passes. These you may want to run overnight since they take a long time to complete (run them an hour before bed each of the next two nights and check before going to sleep that they are still running).
  
     Warning

  Before you proceed with the following, answer these two questions: Are you still under warranty? Does your warranty allow you to open up the machine to check hardware? If you are unsure of the answers to these questions, contact your system manufacturer. :warn:WARNING: The steps that follow can void your warranty!!!
  
  For Part 3: If You Have Errors: If you swap any memory components, follow these steps for ESD safety:
  1. Shut down and turn off your computer.
  2. Unplug all power supplies to the computer (AC Power then battery for laptops, AC power for desktops)
  3. Hold down the power button for 30 seconds to close the circuit and ensure all power drains from components.
  4. Make sure you are grounded by using proper grounding techniques, i.e. work on an anti-static workbench, anti-static desk, or an anti-static pad. Hold something metallic while touching it to the anti-static surface, or use an anti-static wristband to attach to the anti-static material while working. If you do not have an anti-static workbench, desk, or pad, you can use your computer tower/case by finding a metal hold in it, such as a drive bay.
  Once these steps have been followed, it is safe to remove and replace components within your computer.