BSOD randomly happening

Please follow the https://www.sevenforums.com/crashes-d...tructions.html to help us help you. :)

Device Concerns:

Code:

Not Available	ROOT\MEDIA\0000	The drivers for this device are not installed.

Check Device Manager for missing/unknown devices or problems with devices. Device Manager : Hidden Devices may help.

Software Concerns:

Code:

Start Menu\Programs\Driver Identifier
Start Menu\Programs\Free Window Registry Repair

[list][*]We do not recommend automated driver update software. It often finds drivers for devices similar to but not exactly the same as the hardware actually on the system. This can lead to conflicts and blue screen crashes. If you need help finding driver updates for a certain device, please start a thread in Drivers - Windows 7 Forums instead of using software. Driver updates are not always necessary and some updates can actually decrease system stability rather than increase it, so it is usually better not to update unless a device or its driver is causing problems with the system. If it ain't broke, don't fix it.

[*]Many of us on the forums actually do not recommend automated optimization tools for Windows 7. Windows 7 does a much better job of handling its own optimization than its predecessors did. We especially do not recommend registry cleaning as an "optimization" step because automated registry cleaning causes more harm to the registry than it actually repairs.

In the future, if you need help optimizing Windows 7, please post a thread in Performance & Maintenance - Windows 7 Forums or follow the tutorial enclosed in that forum to Optimize Windows 7.

Analysis:

Due to the wide variety of BugCheck codes, I suspect either you have a hardware problem, or the software listed above caused problems on your system. Run some hardware checks.

• If you are overclocking any hardware, please stop.
  
  
• If you have an SSD, make sure the following are up to date:
  • SSD firmware
  • BIOS Version
  • Chipset Drivers
  • Hard disk controller drivers/SATA drivers
  • If you have a Marvell IDE ATA/ATAPI device, make sure the drivers are up to date from the Intel site or Marvell site and not from your motherboard/vendor support site.
  
  
  
• Run all but the advanced tests with SeaTools for HDDs.
  SeaTools for Windows
  
  SeaTools for DOS
  
  
• Monitor temperatures during the following tests.
  
  Use the following programs to monitor the temperatures.
  • Real Temp is a good CPU temperature monitor.
  • Speccy - System Information - Free Download will monitor all hardware temperatures.
  • HWiNFO, HWiNFO32 & HWiNFO64 - Hardware Information and Analysis Tools can be inaccurate for CPU temperatures, but is a good program for GPU temperature monitoring.
  
  
  • Use FurMark: VGA Stress Test, Graphics Card and GPU Stability Test, Burn-in Test, OpenGL Benchmark and GPU Temperature | oZone3D.Net to test the graphics card GPU. Let it run until the GPU temperatures even out or until the GPU temperatures reach a dangerous level (you can find the max temperature for your card on either the nVidia or AMD sites; if you are not sure, ask us). The goal is to get a steady temperature, find out if the GPU is overheating, or to see if there are any artifacts present in the test itself: look for strange pixelated patterns on the screen or colors that do not look like they belong. Then use the |MG| Video Memory Stress Test 1.7.116 Download to test your graphics card memory. Let the memory test run for at least seven passes; the more the better.
    
    
  • Run Hardware - Stress Test With Prime95 to determine any hardware problems. Run all three tests for a few hours each. If you get errors, stop the test and post back here.
    
    
  • Follow the steps for doing CPU stress test using IntelBurnTest
  
  
• Run the boot version of Memtest86+ paying close attention to Parts 2 and 3 of the tutorial. Also, in case Memtest86+ misses anything and comes up with no errors, run the extended version of the Windows Memory Diagnostics Tool for at least five passes. These you may want to run overnight since they take a long time to complete (run them an hour before bed each of the next two nights and check before going to sleep that they are still running).
  
  
     Warning

  Before you proceed with the following, answer these two questions: Are you still under warranty? Does your warranty allow you to open up the machine to check hardware? If you are unsure of the answers to these questions, contact your system manufacturer. WARNING: The steps that follow can void your warranty!!!
  
  
  For Part 3: If You Have Errors: If you swap any memory components, follow these steps for ESD safety:
  
  1. Shut down and turn off your computer.
  2. Unplug all power supplies to the computer (AC Power then battery for laptops, AC power for desktops)
  3. Hold down the power button for 30 seconds to close the circuit and ensure all power drains from components.
  4. Make sure you are grounded by using proper grounding techniques, i.e. work on an anti-static workbench, anti-static desk, or an anti-static pad. Hold something metallic while touching it to the anti-static surface, or use an anti-static wristband to attach to the anti-static material while working. If you do not have an anti-static workbench, desk, or pad, you can use your computer tower/case by finding a metal hold in it, such as a drive bay.
  
  Once these steps have been followed, it is safe to remove and replace components within your computer.