BSOD playing Neverwinter, Warframe, etc. BCCode: 1000007e

[Androshi]

The PSU itself is good, but PSUs keep failing. And, testing the PSU in hand requires some good knowledge of electrical.

It would be better to see the DM log output again, containing the crash dump as stated in post #17.

Just another quick question here's a link to a screenshot I took of the activity level temp and fan speed of my graphics card running default settings on Neverwinter the temp reaches around 70-80 C is this really ok?

 

[Arc]

It is usually said that 70 degrees is not any abnormal temperature for a graphics card. But if you are worried, you may apply a graphics card cooler there.

 

[Androshi]

It is usually said that 70 degrees is not any abnormal temperature for a graphics card. But if you are worried, you may apply a graphics card cooler there.

Quick question I was wondering if a EVGA SuperNOVA NEX 750 G 80 PLUS GOLD Certified 750W Active PFC ATX12V v2.31/EPS 12V v2.91 SLI Ready CrossFire Ready Full Modular PSU would be compatible with my current system.

my specs:
Model: HP Pavillion P6000 series p6744y
CPU: Dual-Core CPU E5800 @ 3.20GHz
Motherboard: FOXCONN 2A8C (CPU 1)
Motherboard chipset: Intel 641 (eaglelake) + ICH7
Memory: 4.00GB Dual-Channel DDR3 @ 399MHz (6-6-6-15)
Storage: 931GB Seagate ST31000340NS ATA Device (SATA)
Video Card: 1024MB ATI AMD Radeon HD 6700 Series (Diamond)
Case: HP Pavillion p6744y
Power Supply: RocketFish 500W 80+
Optical Drive: hp DVD A DH16ABLH ATA Device
Operating System: Windows 7 Home Premium 64-bit SP1

 

[essenbe]

Androshi, from everything I can tell, it would be compatible. The only thing to be concerned about would be your case. Many of the OEM's use non standard cases. The PSU in question is a standard ATX size, which means it will fit in most any standard size case. But, that does not mean it will fit many OEM cases. The listing from where you are looking to buy it, should list the dimensions of the PSU. Just measure your case, and see if it will fit. Otherwise, it should be fine. You should also look at the connections of the motherboard connections and make sure they are standard connections. Many OEMs will make non standard connections too.

 

[ICIT2LOL]

My 2cents Androshi punch the components into this and see what size PSU you require and it will suggest a minimum and recommended size (gives a little more leeway.

eXtreme Power Supply Calculator

 

[Androshi]

It is usually said that 70 degrees is not any abnormal temperature for a graphics card. But if you are worried, you may apply a graphics card cooler there.

I just installed my New PSU into my computer and played Neverwinter on low settings still because my graphics card is making loud noises and the temp skyrockets everytime I put the game on default settings and after a couple of hours my computer just froze and shut down does this mean something is wrong with my graphics card?

 

[Arc]

As you are suspecting it, stress test the Graphics Card using Furmark.
Video Card - Stress Test with Furmark

If the stress test goes fine but the issue continues as it is, you may apply any other card there on a test basis, to see how it goes.

 

[Androshi]

As you are suspecting it, stress test the Graphics Card using Furmark.
Video Card - Stress Test with Furmark

If the stress test goes fine but the issue continues as it is, you may apply any other card there on a test basis, to see how it goes.

Well before I do that stress test again I'd like to wait for my order of canned air to come so I can try spraying the unknown dust maybe under the graphics fan that may cause the insane temp increase before doing so. I appreciate your response though

 

[Arc]

OK, wait for dusting. Let us know the situation after doing it.

 

[Androshi]

OK, wait for dusting. Let us know the situation after doing it.

Well I dusted it off using canned air and tried to play something and it crashed again in less than a minute into gaming. I'm guessing the second solution is thermal paste? If that doesn't work a new video card than?

 

[ICIT2LOL]

OK, wait for dusting. Let us know the situation after doing it.

Well I dusted it off using canned air and tried to play something and it crashed again in less than a minute into gaming. I'm guessing the second solution is thermal paste? If that doesn't work a new video card than?

Androshi my 2 cents worth mate if you do the thermal on the CPU and the GPU - pointless not doing both use this to clean the surfaces Arctic Silver Incorporated - ArctiClean
the use this Arctic Silver Incorporated - Arctic Silver 5
After cleaning and preparing thus surfaces put a vinyl glove on your hand or just cut off one finger and spread a thin film of compound gently on both surfaces, and then place a rice grain sized piece of compound on the CPU lid and the GPU chip and replace the cooling system - DO NOT over tighten many make the mistake of thinking tighter is better but it only need a few seconds for the compound to fill the microscopic gaps / pits in the two mating surfaces when the devices start to heat up. I do not believe in "burning in times" but the choice is personal and yours of course.

 

[essenbe]

How old is your graphics card and is it still under warranty? It should be making no noise at all. Just make sure the noise is coming from your graphics card and not somewhere else. if it is, and still under warranty, I would be on the phone with technical support from the manufacturer of the card.

 

[Androshi]

OK, wait for dusting. Let us know the situation after doing it.

Well I dusted it off using canned air and tried to play something and it crashed again in less than a minute into gaming. I'm guessing the second solution is thermal paste? If that doesn't work a new video card than?

Androshi my 2 cents worth mate if you do the thermal on the CPU and the GPU - pointless not doing both use this to clean the surfaces Arctic Silver Incorporated - ArctiClean
the use this Arctic Silver Incorporated - Arctic Silver 5
After cleaning and preparing thus surfaces put a vinyl glove on your hand or just cut off one finger and spread a thin film of compound gently on both surfaces, and then place a rice grain sized piece of compound on the CPU lid and the GPU chip and replace the cooling system - DO NOT over tighten many make the mistake of thinking tighter is better but it only need a few seconds for the compound to fill the microscopic gaps / pits in the two mating surfaces when the devices start to heat up. I do not believe in "burning in times" but the choice is personal and yours of course.

Well my order of thermal paste is coming soon but can't I use rubbing alcohol and a piece of cloth to clean off the old thermal paste? And I tried restarting my computer after it shutdown but it just kept frozen on one page and played the start up sound but I couldn't type or do anything since it was frozen.

 

[Androshi]

How old is your graphics card and is it still under warranty? It should be making no noise at all. Just make sure the noise is coming from your graphics card and not somewhere else. if it is, and still under warranty, I would be on the phone with technical support from the manufacturer of the card.

I wouldn't know about if it's still under warranty cause I bought this computer on Ebay and it was refurbished so I have little knowledge about it. Also I am 100 percent positive its coming from the GPU since I recently replaced my PSU so the GPU is the only cause for loud noises

 

[Androshi]

Well now my computer problem got a bit worse since after it crashes and I try to restart it the orange light turns on for about 2 seconds and switches off leaving me on the initial start screen and everything else is still working but ya..

 

[Arc]

Is it already done?

 

[Androshi]

Is it already done?

no clue what you mean?

 

[Arc]

Blue texts are hyperlinks ... click on it. You will get the clue.

 

[Androshi]

Blue texts are hyperlinks ... click on it. You will get the clue.

could I use a towel and some rubbing alcohol to clean off the thermal paste?

 

[ICIT2LOL]

Yes you can use anything that dissolves an oily substance as most compounds are oily based - alcohol is a water based solution but go ahead and use what you like. The stuff I referred to cleans more thoroughly and the second solution actually prepares the surfaces before the compound is applied.
You could even lap the surfaces if you wanted to go that extra mile but in all honesty the surfaces would still have microscopic marks and pits in them.