Mounting an HDD with windows installed, on a new PC?

[T1NT1N]

Hi there,

just wondering, is there a way to make a previously installed windows boots on a different PC?

(i tried that this morning with win xp sp3, but it freezes at start-up and doesn't boot, i can choose to run safe mode, but it freezes there too.. so i ended up reinstalling windows again for that new PC)

 

[Petey7]

It's not likely to work. You have drivers installed that to not apply to the different hardware. You also have hardware that does not have drivers installed for it. The mix of the two (or even one of them) will easily make Windows unbootable.

 

[Ztruker]

I've done this successfully a few times with XP but most of the time get the same result you did.

Nothing to lose, right? Try it with Win 7 and see what happens. The only concern I have is whether the copy of Windows 7 you are moving is an OEM versions. If so then it's tied to the original hardware so legally you are not allowed to do this. As an experiment though, it would be interesting to see what happens.

 

[Night Hawk]

Cloning is the correct for seeing one installation on several machines provided you have a volume license. Businesses do that regular with hundreds with one master disk.

Simply moving a drive into a new machine with a different set of hardwares will obviously have the same negative effect regardless of which version since the installation and drivers installed are still tied to the first machine.

When simply going to change the brand of memory here on a new build MS got a call! That's with the 64bit 7.

 

[MacGyvr]

If you try it, expect to wait awhile. It will take some time for Win 7 to install the new drivers, and several reboots may be required. With patience, it should work. You will need to reactivate Windows, however.

 

[Night Hawk]

You would first need to clean everything up as far as existing drivers since removing them ahead of time will also remove the registry entries pointing to them.

For long term use don't bother trying to see that pre-existing install activated unless that will become your main system to start with like an upgrade into newer hardwares. That's where a clean install would be what comes to mind right from the start.

For a quick look not a problem. I tossed a quick temp install on one case here lately to find out what would work and had some interesting results for the old boat anchor!

 

[gregrocker]

It works about half of the time I've tried here, swapping out all of the drivers in a cascade which requires several restarts. However it then runs fine and has never checked out less than perfect using chkdsk, sfc, or performance-wise.

There is a program Paragon Adaptive Restore that prepares the OS by removing all of the drivers first.

And if it won't start the first time, see if you can boot into Safe Mode and swap out your chipset and display driver which also often works.

 

[Night Hawk]

Cleaning off all device drivers except for video and sound if the same drivers work for the video and sound being the same would be the first item. For other mismarches however you could easily end up seeing a blue screen or two until those are tended to.

Having removed all drivers however would be the best move from the start since this is a major change of everything. Your memory, hardware, and even bios configurations between two different systems will be the obstacle for the most part.

 

[arkhi]

Do something to such that it boots it up, then do an upgrade install within the OS. This should replenish all your drivers. However, the booting up part is hard depending on the difference of your hardware. I, for one, never successfully booted a hard drive with Win 7 in it from an old system to practically anything.

The major factor should probably be your chipset, your motherboard, and your processor difference. The greater, the harder.

 

[madtownidiot]

Microsoft starting locking windows installations to the hardware it was originally installed on with windows 2000. Prior to that, you could pull a HDD with windows 95 or 98 installed out of almost any computer and it would boot almost any other computer.

 

[Night Hawk]

That's called the hardware profiling and why it's not advised to bother going to MS to see any previous installation moved reactivated to start with. To simply see if 7 will run on an old case a fast temp install allows the 120 day extended trial. http://www.sevenforums.com/tutorials/875-activation-trial-period-extend-up-120-days.html

 

[MacGyvr]

There is absolutely no reason to uninstall or make any changes to the system before you move the drive to the "new" computer. The only thing that would gain is a minimal amount of disk space taken up by the existing drivers. Windows simply won't load them once that hardware is no longer available. No need to make the process more complicated than it is.

 

[nickiler]

You could reinstall the drive back to its original system and then run sysprep tool to clean up the image http://articles.techrepublic.com.com/5100-22_11-5838633.html

Once the image is clean you can transfer it to another system with different hardware.

I usually run sysprep with the generalize option for migrations.

Without sysprep you have to manually remove the bad stuff.

 

[Night Hawk]

You could reinstall the drive back to its original system and then run sysprep tool to clean up the image SolutionBase: Using Sysprep to create a Windows XP image

Once the image is clean you can transfer it to another system with different hardware.

I usually run sysprep with the generalize option for migrations.

Without sysprep you have to manually remove the bad stuff.

The idea works but Sysprep is mainly for XP not Vista or 7. The best option is planning a clean install from the start and use of the Windows Easy Transfer tool to back up and then restore all user files and settings once all the programs are on fresh.

You also see a new hardware profile created at the same time. You start off with a totally fresh system registry as well without a load of temp folders and other leftovers to contend with.

 

[nickiler]

You could reinstall the drive back to its original system and then run sysprep tool to clean up the image SolutionBase: Using Sysprep to create a Windows XP image

Once the image is clean you can transfer it to another system with different hardware.

I usually run sysprep with the generalize option for migrations.

Without sysprep you have to manually remove the bad stuff.

The idea works but Sysprep is mainly for XP not Vista or 7. The best option is planning a clean install from the start and use of the Windows Easy Transfer tool to back up and then restore all user files and settings once all the programs are on fresh.

You also see a new hardware profile created at the same time. You start off with a totally fresh system registry as well without a load of temp folders and other leftovers to contend with.

That may be the ideal method if your system is running. When you have a stale drive away from its host then reinstalling back and running sysprep should work.

I have only run sysprep on Win7 so it works quite well. I used this method last with Windows Deployment Services during the capture process which will only run on a Win7 that has run sysprep with the generalize switch command.

Sent from my PC36100 using Tapatalk

 

[Night Hawk]

On any new set of hardwares the best results are shown to be from a clean install of the OS especially when the hardwares are not identical. That insures the best detection of all hardwares during the installation process.

A program like Sysprep is mainly for fast use of any image transferred noting that even with that the advice is a minimal install on the first machine before the transfer takes place. You may as well perform a clean install on the new machine if you are going to do that on the old anyways.