Solved Blue screen ACPI error after installing a New Graphics Card plz HELP

[SdSteve760]

I have a Intel DG31PR Motherboard, and with a new Galaxy GeForce GT520 w/2048mb just installed into it I get the below mentioned error... but with out the card installed and using onboard video.. I get no error at all and it boots up just fine...

System is a cpl years old
OS INSTALLED ON NEW DRIVE 1 WEEK AGO

Can anyone help me with this error or know how to correct it.. please help...
thank you very much in advance..

****BLUE SCREEN ERROR MESSAGE****

The BIOS in this system is not fully ACPI compliant. Please contact your system vendor for an updated BIOS.
Technical information:
*** STOP: 0x0000000A5 (0x0000000000001000, 0x0000000000000000, 0x00000000FFFFFFFF, 0x0000000000002000)"

SYSTEM INFO:
7 ultimate 64bit
CPU: intel core 2 duo
E4700 @2.6ghz
Memory: 2gb x 2 dual channel
800mhz
H.D.Seagate sata 1ter.
450 watt PS

 

[panais]

Hi.

You dont have any minidumps in your uploaded folder.

Go to C:\Windows,find the folder with the name Minidump,in this folder find the most recent minidumps and copy paste them in desktop.Then in desktop zip this minidumps and upload them here using the attachment clip.

If the minidump folder is empty,you may need to enable minidumps by following these steps Dump Files - Configure Windows to Create on BSOD

 

[SdSteve760]

The attachment on my original post is a new one please look to see if it has what you are needing .. thanks

 

[panais]

Again

You dont have any minidumps in your uploaded folder.

Minidumps is a specific file created from crash\bsod.

Go to C:\Windows,find the folder with the name Minidump,in this folder find the most recent minidumps and copy paste them in desktop.Then in desktop zip this minidumps and upload them here using the attachment clip.

If the minidump folder is empty,you may need to enable minidumps by following these steps Dump Files - Configure Windows to Create on BSOD You can also use option 2.

 

[SdSteve760]

well can u tell why i wouldnt have any minidumps after i have activated it and went and put my graphics card back in so it would get the BSOD once activated ? any ideas
on this should i try it again ????

Again

You dont have any minidumps in your uploaded folder.

Minidumps is a specific file created from crash\bsod.

Go to C:\Windows,find the folder with the name Minidump,in this folder find the most recent minidumps and copy paste them in desktop.Then in desktop zip this minidumps and upload them here using the attachment clip.

If the minidump folder is empty,you may need to enable minidumps by following these steps Dump Files - Configure Windows to Create on BSOD You can also use option 2.

 

[panais]

Do you use a disk cleanup or any disk cleaners like ccleaner?

If yest stop.

In meantime run http://www.sevenforums.com/tutorials/1538-sfc-scannow-command-system-file-checker.html you may need to run it 2-3 times to "fix" everything.

 

[SdSteve760]

Hi and ty for the suggestion I ran the scan but it did not find any issues, if you have any other ideas I will be glad to try them any an all help is greatly appreciated... ty Steve

Do you use a disk cleanup or any disk cleaners like ccleaner?

If yest stop.

In meantime run http://www.sevenforums.com/tutorials/1538-sfc-scannow-command-system-file-checker.html you may need to run it 2-3 times to "fix" everything.

 

[yowanvista]

Please update your BIOS, it dates back to 2007
http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=18881&ProdId=2839&lang=eng#help

 

[SdSteve760]

Went and created a bootable flash drive to install my updated bios but when I am
in the area where I have to select the file to load for the new bios it starts with A: for the drive and it is actually located in removable disk E: but the system says it does not recognize E: as a valid drive letter so it wont open the file to load the new update on the flash drive.. any ideas what I might be doing wrong have tried using the A: but it says invalid file name... I am listing the file name as follows
IFLASH2 /PR0071.BIO I belive that is correct.. Please any help or advise for this
to help me update my bios... Thanks all help is greatly appreciated... Steve

Please update your BIOS, it dates back to 2007
http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=18881&ProdId=2839&lang=eng#help

 

[yowanvista]

Went and created a bootable flash drive to install my updated bios but when I am
in the area where I have to select the file to load for the new bios it starts with A: for the drive and it is actually located in removable disk E: but the system says it does not recognize E: as a valid drive letter so it wont open the file to load the new update on the flash drive.. any ideas what I might be doing wrong have tried using the A: but it says invalid file name... I am listing the file name as follows
IFLASH2 /PR0071.BIO I belive that is correct.. Please any help or advise for this
to help me update my bios... Thanks all help is greatly appreciated... Steve

Please update your BIOS, it dates back to 2007
http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=18881&ProdId=2839&lang=eng#help

Try the 3rd download "PRG3110H.86A.0071.EB.EXE", it should have an automatic BIOS updater.

 

[SdSteve760]

Went and created a bootable flash drive to install my updated bios but when I am
in the area where I have to select the file to load for the new bios it starts with A: for the drive and it is actually located in removable disk E: but the system says it does not recognize E: as a valid drive letter so it wont open the file to load the new update on the flash drive.. any ideas what I might be doing wrong have tried using the A: but it says invalid file name... I am listing the file name as follows
IFLASH2 /PR0071.BIO I belive that is correct.. Please any help or advise for this
to help me update my bios... Thanks all help is greatly appreciated... Steve

Please update your BIOS, it dates back to 2007
http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=18881&ProdId=2839&lang=eng#help

Try the 3rd download "PRG3110H.86A.0071.EB.EXE", it should have an automatic BIOS updater.

Have got the bios flashed will now try and re install the graphics card and see
if it was the problem will report back after with the results

 

[SdSteve760]

Can someone please look at my dump files attachment

I have added the Dump files to my thread but have not got any response back on them can someone please look an see if they will tell me why my card wont work on the intel motherboard, have tried card on a different system and in worked fine please help