BSOD IRQL_not_less_or_equal 0xA

[Elanaar]

Hi

I'm getting regular BSOD's. Sometimes my computer will run for a couple of hours, sometimes barely 5 minutes without a BSOD

The error showing is IRQL_NOT_LESS_OR_EQUAL with various errors all starting 0xFFFF800...

Below is a link to the zip of the minidump
DUNCAN-PC-21_01_2017_145600_45.zip - Google Drive

 

[ICIT2LOL]

Ok Elanaar as per last time I cannot open your dump files so please follow these and post back

Dump Files - Configure Windows to Create on BSOD
&
Blue Screen of Death (BSOD) Posting Instructions

As soon as we get them we can start to get to grips with your problem.

 

[Elanaar]

Try now, followed all the instructions in the links

DUNCAN-PC-22_01_2017__01116_42.zip - Google Drive

 

[Elanaar]

Sorry to bump, but this problem is driving me nuts. Can anyone look at the dump files?

 

[ICIT2LOL]

Sorry about the delay but myself I cannot see the dumps did you follow those tutorials because it is the way we like dumps to be posted.

 

[Elanaar]

I thought I did before. This is the instructions followed to the letter

http://www.**************/file/xq3kv5iuil54ck9/DUNCAN-PC-25_01_2017_201009_47.zip

 

[ICIT2LOL]

Ok ?Duncan mate I think there is a problem here as per the attached pics is what I am getting when I try to open the two different lots of dumps you have sent.

Now I don't suppose you can remember what the blue screen/s messages were by any chance??

If the worst comes to worst I might have to ask the authour what is going wrong but as a general rule there his no problems with sending the dumps as is.

 

[Elanaar]

Thank you so much for your patience. Here it's is relinked

https://www.**************/download/xq3kv5iuil54ck9

 

[Elanaar]

I don't understand why it's posting as asterisks. The links are from mediafire . Com (it asterisked it when I tried typing it in this post)

 

[Elanaar]

Finally! I misread that last instruction. Sorry for taking up your time and thank you so much for your patience

 

[ICIT2LOL]

Ok got them now and the dump below in code is a very common one and could be literally anything so it means digging through the BSOD dump which I must admit are more than I would put up with.

Probably caused by : [COLOR="Red"]ntoskrnl.exe[/COLOR] ( nt+12452f )

Now there is this one too

SYMBOL_NAME:  [COLOR="red"]IOMap64+1734[/COLOR]

FOLLOWUP_NAME:  MachineOwner

IMAGE_NAME: [COLOR="red"] IOMap64.sys[/COLOR]

BUCKET_ID:  WRONG_SYMBOLS

FAILURE_BUCKET_ID:  WRONG_SYMBOLS

This is something to do with the Asus GPU Tweaking software so are you using that or not? If so it might be an idea to uninstall it for now.

So lets try that first while I go digging elsewhere. By the way it is no trouble and you are not wasting my or anybody's time ti waht we do, plus the fact I am banged up in hospital right now with a broken leg and have a lot of spare time

 

[ICIT2LOL]

Just a quick reply now Duncan there is one problem device listed in the msinfo32 - see pic and I suggest you update the driver for the USB. Trouble is there are two listed in the Gigabyte site GIGABYTE - Motherboard - Socket 1155 - GA-Z77-D3H (rev. 1.0) and to find the right one it mightbe an idea to run PART B: of this ditty of mine.

Using HW Info
PART A:
You can test the volts on the PSU with HW Info HWiNFO, HWiNFO32/64 - Download < download the right bit version and close the right hand window select Sensors and scroll down to the power section where you will see what the volts are doing see my pic. In my pic the section (Nuvoton) with VBATT as a dead give away you are in the section for the rail voltages. There are other section titles and one that pops up often is ITE (sometimes the usual one for Gigabyte boards)
Now the voltage on the different rails have to be within 5% =+/- of what is required or the machine will not work properly if at all.
Limits +/- (minimum - correct - maximum)
12v1 = 11.4 - 12 - 12.6v
12v2 = 11.4 - 12- 12.6v
5v = 4.75 – 5 - 5.25v
3.3v = 3.135 – 3 – 3.465v
-12v = -10.80 - -12 - -13.20v
+5VSB = 4.75 – 5 - 5.25v
The Power good signal voltage at pin 8 on the 24 pin plug (grey cable) should be the same as the 5v rail reading/s
See this for the rail voltage info
PSUs 101: A Detailed Look Into Power Supplies (Section 2.)
The original right hand window shows the machine running and is handy for that but for looking at the components in some detail close it and use the main left hand side panel
FOR OTHER COMPONENTS
PART B:
Open each small square with + in it on the section the components are in and then click on the individual component/s (it will highlight in blue) - in the right hand side will appear all sorts of details including brands speeds and other essential info that particular device. See pic for example.