Solved Constant BSOD's while using network.

[influence]

For some days now, my pc is getting bsod's , mostly during online games or just online streaming.
In the past I've noticed that my memory kits are for 1333 mhz, sadly my p5q3 has a conflict with them and will just freeze, rendering me useless and forced to use them at a lower frequency.
For quite some time i've been using a usb wifi adaptor for internet, which caught my eye to the bsod's that had tcpip.sys and some other network related crashes i managed to read of the forums. Even though now i'm posting from a ftp connection just 2 minutes ago I got the bsod while watching a stream.
My drivers are up to date, pretty sure this is a software issue.
May i get some assistance with someone reading my dumps?

 

[essenbe]

hello, influence You have a number of dump files. They have mostly different error codes and different causes. That is normally indicative of a memory problem.

KMODE_EXCEPTION_NOT_HANDLED (1e)
This is a very common bugcheck.  Usually the exception address pinpoints
the driver/function that caused the problem.  Always note this address
as well as the link date of the driver/image that contains this address.
Arguments:
Arg1: 0000000000000000, The exception code that was not handled
Arg2: 0000000000000000, The address that the exception occurred at
Arg3: 0000000000000000, Parameter 0 of the exception
Arg4: 0000000000000000, Parameter 1 of the exception
 
Probably caused by : [COLOR=red]RTL8192cu.sys[/COLOR] ( RTL8192cu+30e74 )

That is your Realtek RTL8192C Wireless USB drive

DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1)
An attempt was made to access a pageable (or completely invalid) address at an
interrupt request level (IRQL) that is too high.  This is usually
caused by drivers using improper addresses.
If kernel debugger is available get stack backtrace.
Arguments:
Arg1: 00000000979e4292, memory referenced
Arg2: 0000000000000002, IRQL
Arg3: 0000000000000000, value 0 = read operation, 1 = write operation
Arg4: fffff8800185b5c3, address which referenced memory

Use !analyze -v to get detailed debugging information.
BugCheck D1, {4, 2, 1, fffff88003a69448}
[COLOR=red]Probably caused by : afd.sys[/COLOR] ( afd!memmove+b8 )
Followup: MachineOwner

that is your winsock network driver from Windows Update

Use !analyze -v to get detailed debugging information.
BugCheck 3B, {c0000005, fffff88000c26344, fffff880095a8dd0, 0}
[COLOR=red]Probably caused by : memory_corruption[/COLOR]
Followup: memory_corruption

I would suggest you updating the drivers above if you can. If the Realtek driver is from your WiFi Dongle, either update it or get another one. Also make sure all of your Windows updates are current. I'm not sure what you mean by your memory cannot be run at 1333. Your board will run 1333 memory as long as your timings and Dram Voltage are set correctly. Motherboards | P5Q3 | ASUS Global

Please Run Memtest86+

   Information

Please download from this site only http://www.memtest.org/ in the middle of the page are the Download links, you can download the ISO.zip or the Auto USB Flash Drive installer.zip

Extract the Zip file. If you chose the ISO image, burn it to a CD using Windows Disk Image Burner or any Image burner you may have. If you downloaded the Auto USB installer, extract it, insert your USB 2.0 Flash Drive and take note of the drive letter. Run the installer, select the Flash Drive Letter, check the format box and press next. It will install memtest86+ to a flash drive. You can use either V4.20 or V5.01. Boot from your selected media. If you use V5.01 it will tell you to press certain buttons at the start, please press no buttons. The test will begin on it's own and continue to run until you stop it. It needs to run for 8 complete passes or until you receive an error. If you receive an error, stop the test. Even 1 error is a fail. Each pass tests a different part of the ram and each of the 10 tests in each pass tests something different. It takes a minimum of 8 passes to completely test the ram, more passes are better. It is quite a long test and will take several hours depending on how much ram you have. Due to the time length it is best to run overnight. If you have any questions, please do not hesitate to ask​

 

[influence]

Thank you for your insight, to clear up the memory settings, i'm currently running them at 1066 Mhz, voltage on auto as usual, timing on auto aswell, if I set them to 1333 Mhz, sistem faults , freezing, requesting a reset. Think if I can figure out what timings to set them on, this bsod's will stop, sadly I haven't managed while scrolling threads to find the apropiate settings for them.

 

[essenbe]

The frequency, timings and voltage are on a sticker on the sides of the ram sticks. You can also download and install CPUZ (CPU-Z | Softwares | CPUID) and post a screenshot of the memory and spd tabs. On the SPD tabs you can select each DIMM slot. Just post the slots populated with ram.

You won't find the timings in the threads. They are specific to your particular ram model.

 

[influence]

Uhh great info, that explains a lot. Fixed timmings, so far so good, no more bsod while playing or streaming. Thank you kind sir.

 

[essenbe]

You're welcome. I hope it continues to work for you. Keep us posted and let us know how it goes.