Clean Install W7 Home Premium_Prep

[bludgard69]

OK.My bad.
I forgot that I had ReadyBoost in card reader.

So,do I understand right-that i completely wipe my hard drive?

 

[NoN]

Here a more clear tutorial:
http://www.sevenforums.com/tutorials/52291-partition-hard-drive-windows-7-install.html?filter[2]=Hardware and Drivers

If you have follow til EXIT command it is good...now insert your DvDs then install

 

[bludgard69]

OK.Let me check it out.

 

[NoN]

OK.Let me check it out.

The tutorial is very clear to read and full of screenshots...should be easy.

 

[bludgard69]

On a side note----I just got a prompt to upgrade to a new version of MSE.Ever heard of this?:huh:

 

[theog]

If you Typed in command line as below. YES.
DISKPART
LIST DISK
SELECT DISK # (win HD)
CLEAN ALL
CREATE PARTITION PRIMARY
SELECT PARTITION 1
ACTIVE
FORMAT fs=NTFS
ASSIGN
EXIT
EXIT

 

[theog]

If you installed MSE, than YES.

 

[theog]

Few more tutorials:

http://www.sevenforums.com/tutorials/52129-disk-clean-clean-all-diskpart-command.html
http://www.sevenforums.com/tutorials/2668-partition-volume-delete.html?ltr=P
http://www.sevenforums.com/tutorials/2674-partition-volume-create-new.html?ltr=P
http://www.sevenforums.com/tutorials/71432-partition-mark-active.html?ltr=P
http://www.sevenforums.com/tutorials/91339-ssd-optimize-windows-re-installation.html

 

[bludgard69]

OK.I'll post back in a few.

 

[bludgard69]

I'm Back!

You guys rule!

Just want you to know that my first clean-install went quite well.THANKS TO SEVEN FORUMS.

I'll say it again.............

YOU GUYS RULE!!!!!!!

 

[NoN]

You guys rule!

Just want you to know that my first clean-install went quite well.THANKS TO SEVEN FORUMS.

I'll say it again.............

YOU GUYS RULE!!!!!!!

Glad you sorted out!

I guess we got worry at one time, but now it's a 100% receiver signal!

 

[gregrocker]

Determine which Disk you want to clean from the LIST DISK list which is produced. You should only have one DISK 0.

Did you get it cleaned ok, then create the partition and format using DISKPART commands?

Re: Your activation issue: Did you install the correct version for your OEM license? Are you reading and then inputting the Product Key correctly? If so, then call MS to activate.

Be sure to check optional Windows Updates for any newer drivers. If any drivers are then missing in device Manager, find them on the Support Downloads webpage for your computer model.

Install programs slowly over time so you can check performance after each. Don't let any creep into your msconfig>Startup programs list - I only allow MSE and gadgets in there.

Once you have it running as you want, use CCleaner "Run Cleaner" and Registry tab then Auslogics Disk and Registry Defraggers to clean and order the HD perfectly..

 

[bludgard69]

Determine which Disk you want to clean from the LIST DISK list which is produced. You should only have one DISK 0.

Did you get it cleaned ok, then create the partition and format using DISKPART commands?

Be sure to check optional Windows Updates for any newer drivers. If any drivers are then missing in device Manager, find them on the Support Downloads webpage for your computer model.

Install programs slowly over time so you can check performance after each. Don't let any creep into your msconfig>Startup programs list - I only allow MSE and gadgets in there.

Once you have it running as you want, use CCleaner "Run Cleaner" and Registry tab then Auslogics Disk and Registry Defraggers to clean and order the HD perfectly..

Yeah,It's clean as a whistle.
Runs like a true thoughrobred.
Was a little intimidating.Not for no good reason,though.

 

[bludgard69]

Only one problem.

I put in the product key from bottom of my laptop,yet I think that that isn't enough.

 

[gregrocker]

Are you sure you installed the correct version for your OEM license? What does it say at Computer>Properties?

Click on Activate now so it can connect to the internet to activate. If it fails, make sure you input the exact Product Key and read it correctly from COA sticker. If it still fails, call MS at the number given to help you activate.

 

[bludgard69]

OK.I'll give them a call.
Correct product key.
I'll be back.

 

[bludgard69]

Surfs Up Dude!

Are you sure you installed the correct version for your OEM license? What does it say at Computer>Properties?

Click on Activate now so it can connect to the internet to activate. If it fails, make sure you input the exact Product Key and read it correctly from COA sticker. If it still fails, call MS at the number given to help you activate.

The phone call worked.
I'm Genuine again!
Alright,I'm going to lay down for a while.I'll be back to sing your praises later. You all have made me a happy man!Hope I can return the favor sometime.

Yeah.Right.Imagine that.

 

[bludgard69]

What will I do next?

 

[gregrocker]

Here:

Be sure to check optional Windows Updates for any newer drivers. If any drivers are then missing in device Manager, find them on the Support Downloads webpage for your computer model. Get Adobe reader and Flash player, Java Runtime from their sites.

Install programs slowly over time so you can check performance after each. Don't let any creep into your msconfig>Startup programs list - I only allow MSE and gadgets in there.

Once you have it running as you want, use CCleaner "Run Cleaner" and Registry tab then Auslogics Disk and Registry Defraggers to clean and order the HD perfectly..

 

[electrotune1200]

What will I do next?

Make a system image!

http://www.sevenforums.com/tutorials/663-backup-complete-computer-create-image-backup.html?filter[2]=Backup Restore