blue screen error 0x000000E1

[writhziden]

You need to choose the top BIOS update: 1.60 2/8/2012 Instant Flash 2.43MB Add Turbo UCC function for AM3+. You can tell it is the most updated because the numbers go up from 1.10 to 1.60 for the BIOS version column. Use either the DOS or Instant Flash version to flash the BIOS. They are safer to use.

I would also recommend downloading 1.50 11/18/2011 Instant Flash 2.42MB Update CPU code. This is your current version, so you can flash back to it if needed. Flash the 1.60 first, though.


You need to run sfc /scannow in an http://www.sevenforums.com/tutorials/783-elevated-command-prompt.html

 

[KiLLuA]

seems a big problem happened here , i downloaded the BIOS update file and later i restarted the computer to boot it up and there wasn't a back key to check the right selection so i restarted the PC , and i try to open it now and it don't start with the motherboard boot window (first screen) is there anyway to fix it ?

 

[writhziden]

Was this before or after flashing the BIOS?

 

[KiLLuA]

i didnt get chance to update it i just viewed the flash menu but i figured that i was in the UEFI flashing menu , so i restarted the PC and i didnt open after that.

 

[writhziden]

That's odd... I wonder if you have a bad power supply. Can you borrow one to check?

 

[KiLLuA]

you miss understood me , the fans working and the processor fan working the little screen on the motherboard is led up , but still nothing on the screen.

 

[writhziden]

Still could be PSU if it cannot power the graphics card, but I see why you are somewhat ruling it out. Still may be a good thing to check. Also, see if your graphics card needs to be re-seated. Avoid Static Damage to Your PC when doing so.

You could also try a hard reset: use hard reset to resolve hardware and software issues which works with all computers, not just HP Pavilions, minus the HP updates step.

 

[KiLLuA]

the motherboard doesn't boot, and there is a small screen on the motherboard that is called Dr.debug reads 10, the speaker that is attached to the motherboard directly wont "beeb", i did the hard reset steps, and reattached the vigacard. any ideas please ?

 

[KiLLuA]

what i did from what i just said before can damge the motherboard, like it is dead? or i can go to the customer care of the manufacture to replace the damaged bios ?

 

[writhziden]

I do not see how the steps you did could have caused any damage to the BIOS unless you started to execute the flash of the BIOS and then interrupted it by resetting. If all you did was view the BIOS with the BIOS update utility listed, that should not have caused the issues you are facing. Can you walk me through step-by-step exactly what you did before this occurred?

 

[KiLLuA]

yes i think that what exactly happened " started to execute the flash of the BIOS and then interrupted it by resetting", i thought you understood that from what i said, sorry for not being clear.

 

[writhziden]

I was under the impression that you just viewed the version available to flash to... You should try to clear the CMOS and see if it helps. You will have to do it on the board itself since you cannot view your BIOS through the computer. How To Clear CMOS (Reset BIOS)

Make sure all power is drained first from the board by shutting down and turning off the computer, unplugging it from the wall, and then holding the power button down for 30 seconds to complete the circuit and drain power from the board itself. Then clear the CMOS using one of the two (remaining) methods in that link; the jumper method or the battery method should work.

Post back the results once those steps are completed.

 

[KiLLuA]

i removed the only circular battery of the motherboard and re attached it again and switched the PC on still blank screen and no beeb , so i tryed the 2nd option about the jumper thing i removed it from its slot was 3 pins the jumper used 1 , 2 slot so i changed it to 2 ,3 and turned the PC on its the same condition

 

[writhziden]

Does any screen show on the monitor itself, or does it not even turn on?

 

[KiLLuA]

it doesn't turn on with anyscreen

 

[writhziden]

Try removing all but one stick of RAM. Beyond that, you will need to send it in to the manufacturer or take it to a repair shop where they can flash it for you.

In the future, NEVER interrupt a BIOS flash. It is not like updating drivers; the results can be catastrophic as you are seeing...

 

[KiLLuA]

so to be certain of what i will do : i'll remove the processor with it's fan - the vigacard - hard disk - cd room - the battery that on board and leave the motherboard with just 1 slot of ram then i turn the pc on?

 

[writhziden]

I meant remove all RAM but one module. You can remove everything else, as well (except the CPU and fan and CMOS battery, those are necessary), and see if that allows you to get into the BIOS.

 

[KiLLuA]

thanks alot for help Writhziden, all those tries failed i think it is damged as you said and i'll take to get repaired thanks again

 

[writhziden]

You're welcome. Sorry about the flash failure. Let us know how things go after repair and if you still need troubleshooting.