Solved BSOD 0x0000003b file ntoskrnl.exe+73969

[mantuse]

Please help, how to fix this error ntoskrnl.exe+73969r?

 

[Arc]

Is there any specific reason behind enabling driver verifier? There is only one crash dump in the uploaded zip, so we cannot justify it. And Driver Verifier is supposed to cause BSODs by definition.

Disable Driver Verifier.

If it causes any further BSOD in the normal mode, report us back.
__________________________________________________________

BugCheck 3B, {c000001d, fffff80002f95bed, fffff8800351b9f0, 0}

Probably caused by : ntkrnlmp.exe ( nt!HvpGetCellPaged+10d )

Followup:     MachineOwner
---------

Verify Flags Level 0x0000092b

 

[mantuse]

This are all my minidump files.

 

[mantuse]

Get new BSOD

 

[Arc]

Crash dump reports a hardware issue.

BugCheck A, {fffff880277821bd, 2, 1, fffff80002abf8f1}
[COLOR=Red]
Probably caused by : hardware[/COLOR] ( nt!ExpReleaseResourceForThreadLite+221 )

Followup:     MachineOwner
---------

And verifier verifies drivers, not the hardware. You should not have enabled it at all at the first place.

To go hardware troubleshooting for such an old computer, first of all we need to know the system heat. Is the computer hot? Report us the heat of the computer after a couple of hours of your normal usage. Upload a screenshot of the summery tab of Speccy. Alternatively, you can publish a Speccy snapshot too: http://www.sevenforums.com/tutorials/311593-speccy-publish-snapshot-your-system-specs.html .
________________________________________________________

BiosVersion = 2105   
[COLOR=Red]BiosReleaseDate = 05/26/2009[/COLOR]
SystemManufacturer = System manufacturer
SystemProductName = P5Q3 DELUXE
SystemFamily = To Be Filled By O.E.M.
SystemVersion = System Version
SystemSKU = To Be Filled By O.E.M.

 

[mantuse]

Speccy snapshot http://speccy.piriform.com/results/hfcvOzf2nRbzkK8ULW52e61

 

[Arc]

OK. It looks fine. Now let us have some hardware tests.

Stress test the Graphics Card using Furmark.

Video Card - Stress Test with Furmark
​

Take a screenshot of the furmark window before closing it. Upload the screenshot for us. Also let us know if you have experienced any crash/BSOD and/or artifacts during the test.

Stress test the CPU.

Hardware - Stress Test With Prime95
​

It saves the result as a .txt file in the prime95's folder. Upload the file for us.

Check if the Power Supply Unit (PSU) supplying adequate power to the computer or not.

eXtreme Power Supply Calculator
​

Also let us know the wattage of the installed PSU.

Let us know the results.

 

[mantuse]

eXtreme Power Supply Calculator results:

Load Wattage: 377 W
Recommended UPS rating: 750 VA
Recommended PSU Wattage: 427 W

My PSU: Codegen 400x, ~400W

 

[mantuse]

How long need run Hardware - Stress Test With Prime95?

 

[Arc]

How long need run Hardware - Stress Test With Prime95?

As said there: at least two hours or errors come.

6. Leave the test running for up to 2 hours, unless errors occur sooner. Errors will show up by one or more of the workers stopping.

​

eXtreme Power Supply Calculator results:

Load Wattage: 377 W
Recommended UPS rating: 750 VA
Recommended PSU Wattage: 427 W

My PSU: Codegen 400x, ~400W

So your PSU is less that what needed. 400W is insufficient, and which is alone enough for all the issues, but may not be the only one. You need to get a PSU with higher wattage, and then continue with the other tests.

 

[mantuse]

How to save Prime95 files, I run 2h 16min., but all files gone. I can't upload this test results.

 

[mantuse]

Test results:

 

[mantuse]

Thanks for the help, but problem solved myself. It was not PSU problem.

 

[Arc]

Thanks for the help, but problem solved myself? It was not PSU problem.

Make it clear?

 

[mantuse]

In my case RAM not work in 1600 MHz frequency, I put in another two stick of RAM with 1333MHz frequency, and problem gone. PC working steadily, tested 48h and no BSOD.

 

[Arc]

In my case RAM not work in 1600 MHz frequency, I put in another two stick of RAM with 1333MHz frequency, and problem gone. PC working steadily, tested 48h and no BSOD.

But https://www.asus.com/Motherboards/P5Q3_DeluxeWiFiAP_n/specifications/ says ....

View attachment 381992
​

So XMP should not be a problem there, as it appears.

Anyway, if it runs stable then all is well.

EDIT: A closer view reveals:

** DDR3 2000(O.C.)/1600, it is suggested to use one DIMM per channel
​

There are 4 slots, 2 channels. And you are populating 3 slots, first, third and fourth. And here it contradicts.

Your observation is right. Either you have to stay at 1333 MHz or you have to remove one RAM stick.

Still, dont overlook the PSU. 400W is insufficient as your calculations revealed.

 

[mantuse]

I know that must work with 1600, but .....Maybe you understand more?

 

[mantuse]

Edit

 

[Arc]

It is nor understanding, mate. It is reading.

1600 MHz should work there, under a caution given by the board manufacturer that 1600 MHz will work when one DIMM per channel is used. And you have populated both the DIMMs of a channel.

And here it contradicts.

 

[mantuse]

I use two stick of RAM in slots #1 and #3 with 1600MHz, and get BSOD, now I put another two stick of RAM with 1333MHz in slots #2 and #4 with 1333MHz.