Solved Help need update driver!?

[Jager1112]

Help with this errors!

 

[ICIT2LOL]

Ok Jager now mate it would be nice to know why these are causing you any issues and if so what are they?

Plus an English translation of them would be good.

 

[derekimo]

Try the chipset and USB drivers from your motherboard site,

P8H67 Downloads

 

[Jager1112]

Ok Jager now mate it would be nice to know why these are causing you any issues and if so what are they?

Plus an English translation of them would be good.

PCI Simple Communications Controller I dont know what they are think thats internet!

 

[Jager1112]

Try the chipset and USB drivers from your motherboard site,

P8H67 Downloads

View attachment 396032

Thank you i am trying! Down loading

 

[Jager1112]

Yes it got the two but the third is left i havent a clue what they are?

 

[ICIT2LOL]

PCI Simple Communications Controller I dont know what they are think thats internet!

Ok mate it probably is I am guessing it is referring to the LAN (Ethernet) connection. Now pulling the driver up for it reveals there are two different drivers and that needs yo to find out which one it is.
Now I find these things out by using this ditty of mine
Using HW Info
PART A:
You can test the volts on the PSU with HW Info HWiNFO, HWiNFO32/64 - Download < download the right bit version and close the right hand window select Sensors and scroll down to the power section where you will see what the volts are doing see my pic. In my pic the section (Nuvoton) with VBATT as a dead give away you are in the section for the rail voltages. There are other section titles and one that pops up often is ITE (sometimes the usual one for Gigabyte boards)
Now the voltage on the different rails have to be within 5% =+/- of what is required or the machine will not work properly if at all.
Limits +/- (minimum - correct - maximum)
12v1 = 11.4 - 12 - 12.6v
12v2 = 11.4 - 12- 12.6v
5v = 4.75 – 5 - 5.25v
3.3v = 3.135 – 3 – 3.465v
-12v = -10.80 - -12 - -13.20v
+5VSB = 4.75 – 5 - 5.25v
The Power good signal voltage at pin 8 on the 24 pin plug (grey cable) should be the same as the 5v rail reading/s
See this for the rail voltage info
PSUs 101: A Detailed Look Into Power Supplies (Section 2.)
The original right hand window shows the machine running and is handy for that but for looking at the components in some detail close it and use the main left hand side panel
FOR OTHER COMPONENTS
PART B:
Open each small square with + in it on the section the components are in and then click on the individual component/s (it will highlight in blue) - in the right hand side will appear all sorts of details including brands speeds and other essential info that particular device. See pic for example.

Now you only need to use PART B: and when you open the network section it will give you exactly the device brand model and a ton of details about it you only need to know which is installed in your machine and then pick the correct driver from the download listing in the pic I have attached. The other pic is to give you some idea of how to find those details. You will also see those details you mentioned which you referred to.

Edit: I meant to add looking at those downloads it is probably top download.

 

[Jager1112]

Ok mate it probably is I am guessing it is referring to the LAN (Ethernet) connection. Now pulling the driver up for it reveals there are two different drivers and that needs yo to find out which one it is.
Now I find these things out by using this ditty of mine
Using HW Info
PART A:
You can test the volts on the PSU with HW Info HWiNFO, HWiNFO32/64 - Download < download the right bit version and close the right hand window select Sensors and scroll down to the power section where you will see what the volts are doing see my pic. In my pic the section (Nuvoton) with VBATT as a dead give away you are in the section for the rail voltages. There are other section titles and one that pops up often is ITE (sometimes the usual one for Gigabyte boards)
Now the voltage on the different rails have to be within 5% =+/- of what is required or the machine will not work properly if at all.
Limits +/- (minimum - correct - maximum)
12v1 = 11.4 - 12 - 12.6v
12v2 = 11.4 - 12- 12.6v
5v = 4.75 – 5 - 5.25v
3.3v = 3.135 – 3 – 3.465v
-12v = -10.80 - -12 - -13.20v
+5VSB = 4.75 – 5 - 5.25v
The Power good signal voltage at pin 8 on the 24 pin plug (grey cable) should be the same as the 5v rail reading/s
See this for the rail voltage info
PSUs 101: A Detailed Look Into Power Supplies (Section 2.)
The original right hand window shows the machine running and is handy for that but for looking at the components in some detail close it and use the main left hand side panel
FOR OTHER COMPONENTS
PART B:
Open each small square with + in it on the section the components are in and then click on the individual component/s (it will highlight in blue) - in the right hand side will appear all sorts of details including brands speeds and other essential info that particular device. See pic for example.

Now you only need to use PART B: and when you open the network section it will give you exactly the device brand model and a ton of details about it you only need to know which is installed in your machine and then pick the correct driver from the download listing in the pic I have attached. The other pic is to give you some idea of how to find those details. You will also see those details you mentioned which you referred to.

Edit: I meant to add looking at those downloads it is probably top download.

Yes it worked thanik you thank you thank you thank you! Why is it lan dho i dont want any one to connect with me:sarc:

 

[ICIT2LOL]

Now downloading that Ethernet driver is not going to connect anyone to you if you are using wifi for the net connection. The Ethernet can only connect you to the broadband service if you have a cable connected from your machine to the modem/router.

having said that you do not have to install the driver if you do not want to it's your choice.

 

[Jager1112]

Now downloading that Ethernet driver is not going to connect anyone to you if you are using wifi for the net connection. The Ethernet can only connect you to the broadband service if you have a cable connected from your machine to the modem/router.

having said that you do not have to install the driver if you do not want to it's your choice.

Okej thank you for clarifying that.

I going to mark thread as solved!