Solved BSOD Crash After startup about 5mins after.

[AngryCircle]

This is not unusual, we may have to bump the voltage a couple of times.
From +28,000 errors to 4,000 errors, we are making progress.

Go to BIOS again:
Select 'NB Voltage Controls'
Select the +200mV

This will give you 1.30V for the NB.
Run Memtest86+ again, for 7 passes or overnight. If you get any errors, red lines across the screen, you can stop the test and post the results here.

i cannot go any further then 130mV because thats the last option on there.

 

[Dave76]

The manual says it has a +30mV to +360mV range, which is normal for your system.

Did you try hitting the down arrow, there should be higher voltages on the list.

If that is the limit on your BIOS then go to +130mV for the NB Voltage.

And Then go to 'Memory Voltage Control'
Select the +50mV

This will give you 1.85V for the RAM.

Run Memtest86+ again, for 7 passes or overnight. If you get any errors, red lines across the screen, you can stop the test and post the results here.

 

[AngryCircle]

Ok just so you know i've set it to the settings which you've asked.

also took a screenshot showing you what i see.

Just going to run the test now. and it normally fails on the first test (2seconds in).

 

[Dave76]

Select the +120mV for the NB Voltage.

That will give you 1.22V.


If this test fails, take one of the RAM cards out, leave the settings where they are now and Run Memtest86+ again, for 7 passes or overnight. If you get any errors, you can stop the test and post the results here.

Pass or fail, let me know, then put the RAM card back in the same slot and take out the other one, run memtest86+ again, same drill.

 

[AngryCircle]

Select the +120mV for the NB Voltage.

That will give you 1.22V.


If this test fails, take one of the RAM cards out, leave the settings where they are now and Run Memtest86+ again, for 7 passes or overnight. If you get any errors, you can stop the test and post the results here.

Pass or fail, let me know, then put the RAM card back in the same slot and take out the other one, run memtest86+ again, same drill.

ok, here are the results from the voltage changes.

NB - +120mV
Mem - +50mV

 

[Dave76]

OK follow the single RAM card tests in the last post.

Were looking for a bad RAM card and/or bad motherboard slot.

Let me know the results.

 

[AngryCircle]

OK follow the single RAM card tests in the last post.

Were looking for a bad RAM card and/or bad motherboard slot.

Let me know the results.

hey sorry been abit busy, so sorry im taking time, ill try get these tests done when i get abit of spare time.

 

[Dave76]

That's ok, happens to all of us.

Let us know when you get time and the results.

 

[AngryCircle]

That's ok, happens to all of us.

Let us know when you get time and the results.

Hello, sorry about how late this reply is lol.

just lost my job so been busy.

So about this memtest. im going to be handing in this pc for repairs on the RAM as i think there has to be something wrong with it. plus i have a year warranty so its free of charge.

But also i noticed another thing about the back of my PC where i plug in my HDMI lead.

and it was bent at about 90 degrees haha. Could this be the problem to my blue screen? Just a theory tho cause its pritty screwed up the lead.

 

[Dave76]

If you are using the HDMI cable, it definately could be causing the crashes.
Try using another port and cable if you have one.

I would have them fix the RAM and the HDMI connection.

 

[AngryCircle]

If you are using the HDMI cable, it definately could be causing the crashes.
Try using another port and cable if you have one.

I would have them fix the RAM and the HDMI connection.

sweet i really hope its this HDMI.

its not the port that is broken its the lead plugged in. its bent.

 

[AngryCircle]

Hey, i hope theres someone still here to help .

i'm still getting bsod alot even after a change of the HDMI.

so ive run the pc in safe mode. Now not getting any BSOD. i assume that a driver is causing the problem of this BSOD. i personally think its something to do with Audiolog.exe this uses quite high CPU and when i disable it in task manager i hear a loud buzzing noise until i reenable it. So my point is that when im about to blue screen i get that buzzing noise just before and then up untill i reset the pc.

please any suggestions on this would be grateful.

 

[Dave76]

OK follow the single RAM card tests in the last post.

Were looking for a bad RAM card and/or bad motherboard slot.

Let me know the results.

That's ok, happens to all of us.

Let us know when you get time and the results.

Hello, sorry about how late this reply is lol.

So about this memtest. im going to be handing in this pc for repairs on the RAM as i think there has to be something wrong with it. plus i have a year warranty so its free of charge.

But also i noticed another thing about the back of my PC where i plug in my HDMI lead.

and it was bent at about 90 degrees haha. Could this be the problem to my blue screen? Just a theory tho cause its pritty screwed up the lead.

Did you return the computer for repairs?
What did they find/replace?

Either way, did you run memtest86+ again to confirm if the RAM is still giving errors or not?

It is best to get all the hardware issues resolved first, these can cause driver faults.

 

[AngryCircle]

OK follow the single RAM card tests in the last post.

Were looking for a bad RAM card and/or bad motherboard slot.

Let me know the results.

That's ok, happens to all of us.

Let us know when you get time and the results.

Hello, sorry about how late this reply is lol.

So about this memtest. im going to be handing in this pc for repairs on the RAM as i think there has to be something wrong with it. plus i have a year warranty so its free of charge.

But also i noticed another thing about the back of my PC where i plug in my HDMI lead.

and it was bent at about 90 degrees haha. Could this be the problem to my blue screen? Just a theory tho cause its pritty screwed up the lead.

Did you return the computer for repairs?
What did they find/replace?

Either way, did you run memtest86+ again to confirm if the RAM is still giving errors or not?

It is best to get all the hardware issues resolved first, these can cause driver faults.

well so far i havent been able to due to recent loss of job so i cant pay for repairs atm.

 

[Dave76]

You had mentioned it is under warranty, anyway we can continue testing.

Follow the testing procedure here: RAM - Test with Memtest86+

You are looking for bad RAM cards, bad motherboard slots, follow the guide and let us know the results.

 

[AngryCircle]

You had mentioned it is under warranty, anyway we can continue testing.

Follow the testing procedure here: RAM - Test with Memtest86+

You are looking for bad RAM cards, bad motherboard slots, follow the guide and let us know the results.

this looks like software related as well so i will be charged for that so cant really take it in yet.

you know a way i can completely wipe everything on my pc? expect for windows ofcause as i dont have a CD because it come installed already.

i would like for it to be like i just turned it on with absolutely noting changed.

 

[Dave76]

Did you make another partition for your data?
For example, C drive for the OS and D drive for your personal data.
If you set it up this way you can make an image backup of your partitions and Secure Erase the HDD and restore the OS partition.
If everything is in one partition the only way to do that is manually select each folder and delete them, then they are still recoverable.

 

[AngryCircle]

Did you make another partition for your data?
For example, C drive for the OS and D drive for your personal data.
If you set it up this way you can make an image backup of your partitions and Secure Erase the HDD and restore the OS partition.
If everything is in one partition the only way to do that is manually select each folder and delete them, then they are still recoverable.

i didnt make and partitions, the pc come pre built and everything installed to it so i dont know what to do.

 

[Dave76]

Run memtest86+ again to see if you are still getting errors.

If you get any errors, follow this tutorial to test the RAM in different slots.

RAM - Test with Memtest86+