Random BSOD

[hdfsi]

I get a random blue screen of death and i cant figure out whats causing them. Dumps included if someone could help it would be great.

RAM----

View attachment 160599

View attachment 160600

View attachment 160601

View attachment 160602


View attachment 160603

 

[yowanvista]

http://www.sevenforums.com/crashes-debugging/96879-blue-screen-death-bsod-posting-instructions.html

 

[hdfsi]

I have included the bsod and the folder from the BSOD Dump & System File Collection app and included the HTML doc from the System Health Report.

 

[yowanvista]

Your Rt64win7.sys which is a Realtek NIC driver needs to be updated
Realtek

*******************************************************************************
*                                                                             *
*                        Bugcheck Analysis                                    *
*                                                                             *
*******************************************************************************

IRQL_NOT_LESS_OR_EQUAL (a)
An attempt was made to access a pageable (or completely invalid) address at an
interrupt request level (IRQL) that is too high.  This is usually
caused by drivers using improper addresses.
If a kernel debugger is available get the stack backtrace.
Arguments:
Arg1: fffff68000100580, memory referenced
Arg2: 0000000000000000, IRQL
Arg3: 0000000000000000, bitfield :
    bit 0 : value 0 = read operation, 1 = write operation
    bit 3 : value 0 = not an execute operation, 1 = execute operation (only on chips which support this level of status)
Arg4: fffff80002ae0ae2, address which referenced memory

Debugging Details:
------------------


READ_ADDRESS: GetPointerFromAddress: unable to read from fffff80002d030e0
 fffff68000100580 

CURRENT_IRQL:  0

FAULTING_IP: 
nt!MiAgeWorkingSet+1c2
fffff800`02ae0ae2 488b19          mov     rbx,qword ptr [rcx]

CUSTOMER_CRASH_COUNT:  1

DEFAULT_BUCKET_ID:  VISTA_DRIVER_FAULT

BUGCHECK_STR:  0xA

PROCESS_NAME:  dllhost.exe

TRAP_FRAME:  fffff880033167a0 -- (.trap 0xfffff880033167a0)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=0000007ffffffff8 rbx=0000000000000000 rcx=fffff68000100580
rdx=0000000000000001 rsi=0000000000000000 rdi=0000000000000000
rip=fffff80002ae0ae2 rsp=fffff88003316930 rbp=0000000000100580
 r8=0000000000000001  r9=fffffa80043097a8 r10=0000000000000005
r11=0000000000000000 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0         nv up ei ng nz na pe cy
nt!MiAgeWorkingSet+0x1c2:
fffff800`02ae0ae2 488b19          mov     rbx,qword ptr [rcx] ds:fffff680`00100580=????????????????
Resetting default scope

LAST_CONTROL_TRANSFER:  from fffff80002acc469 to fffff80002accf00

STACK_TEXT:  
fffff880`03316658 fffff800`02acc469 : 00000000`0000000a fffff680`00100580 00000000`00000000 00000000`00000000 : nt!KeBugCheckEx
fffff880`03316660 fffff800`02acb0e0 : 00000000`00000000 00000980`00000000 00000000`00040000 00000000`0000000b : nt!KiBugCheckDispatch+0x69
fffff880`033167a0 fffff800`02ae0ae2 : 00000003`00000000 0a100001`31738025 00000000`00000000 00000000`000000a1 : nt!KiPageFault+0x260
fffff880`03316930 fffff800`02b4da0e : fffffa80`043097a8 fffff880`00000001 00000000`00000001 fffff880`03316bb0 : nt!MiAgeWorkingSet+0x1c2
fffff880`03316ae0 fffff800`02ae16e2 : 00000000`00005dd7 00000000`00000000 fffffa80`00000000 00000000`00000004 : nt! ?? ::FNODOBFM::`string'+0x49926
fffff880`03316b80 fffff800`02ae196f : 00000000`00000008 fffff880`03316c10 00000000`00000001 fffffa80`00000000 : nt!MmWorkingSetManager+0x6e
fffff880`03316bd0 fffff800`02d70166 : fffffa80`03c37b60 00000000`00000080 fffffa80`03baf9e0 00000000`00000001 : nt!KeBalanceSetManager+0x1c3
fffff880`03316d40 fffff800`02aab486 : fffff880`009e7180 fffffa80`03c37b60 fffff880`009f1fc0 2d6e6fa9`fdffddb7 : nt!PspSystemThreadStartup+0x5a
fffff880`03316d80 00000000`00000000 : fffff880`03317000 fffff880`03311000 fffff880`03316820 00000000`00000000 : nt!KxStartSystemThread+0x16


STACK_COMMAND:  kb

FOLLOWUP_IP: 
nt!MiAgeWorkingSet+1c2
fffff800`02ae0ae2 488b19          mov     rbx,qword ptr [rcx]

SYMBOL_STACK_INDEX:  3

SYMBOL_NAME:  nt!MiAgeWorkingSet+1c2

FOLLOWUP_NAME:  MachineOwner

MODULE_NAME: nt

DEBUG_FLR_IMAGE_TIMESTAMP:  4a5bc600

IMAGE_NAME:  memory_corruption

FAILURE_BUCKET_ID:  X64_0xA_nt!MiAgeWorkingSet+1c2

BUCKET_ID:  X64_0xA_nt!MiAgeWorkingSet+1c2

Followup: MachineOwner
---------

 

[hdfsi]

here is another one.

 

[yowanvista]

here is another one.

The Realtek driver should be updated and remove any AVG software
Use MSE instead, run a scan of Malwarebytes

Please remove any CD virtualization programs such as Daemon Tools and Alcohol 120%. They use a driver, found in your dmp, sptd.sys, that is notorious for causing BSODs. Use this SPTD uninstaller when you're done: DuplexSecure - Downloads
You can use MagicDisc as an alternative.

sptd.sys        fffff880`01048000    fffff880`011aa000    0x00162000    0x4ceba9d9    23/11/2010 15:47:37

AVGIDSDriver.Sys        fffff880`061d0000    fffff880`061fb000    0x0002b000    0x4da72aa9    14/04/2011 21:11:05                
AVGIDSEH.Sys        fffff880`017f1000    fffff880`017fb000    0x0000a000    0x4d634838    22/02/2011 09:23:04                
AVGIDSFilter.Sys        fffff880`04015000    fffff880`04020000    0x0000b000    0x4d5370b9    10/02/2011 08:59:37                
avgldx64.sys        fffff880`040e8000    fffff880`04137000    0x0004f000    0x4d269857    07/01/2011 08:36:39                
avgmfx64.sys        fffff880`02c4c000    fffff880`02c5b000    0x0000f000    0x4d6ce5ab    01/03/2011 16:25:15                
avgrkx64.sys        fffff880`016bf000    fffff880`016cb000    0x0000c000    0x4d80c3ea    16/03/2011 18:06:34                
avgtdia.sys        fffff880`02d21000    fffff880`02d81000    0x00060000    0x4d9a3e1b    05/04/2011 01:54:35

 

[hdfsi]

I went for a bit with out getting one but i just got one.

 

[yowanvista]

The last dump concerns memory management
http://www.sevenforums.com/tutorials/105647-ram-test-memtest86.html

Please update the realtek driver

 

[hdfsi]

Ok i have updated the realtek driver and i ran Memtest all night i got 15passes with 0 errors.

 

[hdfsi]

Got another one :/

 

[hdfsi]

Got another one.. Seems like when i updated the realtek driver i get more BSOD..

 

[yowanvista]

Got another one.. Seems like when i updated the realtek driver i get more BSOD..

For some reason the sptd.sys driver is still being loaded. Use the Deplex Secure software provided earlier to remove that sptd.sys

 

[hdfsi]

Thanks If i get another one i will upload it.

 

[Dave76]

First, fill in your system specs so we can see what hardware you have.

Your CPUZ tabs from the first post are showing some strange RAM settings.

Have you overclocked the RAM or CPU?

If you have OC'ed, reset to defaults, see if the BSoDs stop.

If not, then set your DRAM frequency to 667MHz.

With motherboard, CPU and RAM specs we can give better advice.

 

[hdfsi]

Ok i have updated my specs. I Oc'ed my CPU and my ram speed increased. I got another one i will upload it. But before i overclocked my CPU i was getting blue screens.

Edit- I set my cpu to auto overclock and it set it back down to default which is 2.93Ghz. My RAM went back down to 686MHz.

 

[Dave76]

If you were having BSoDs before OC'ing, You shouldn't OC until you fix the cause.

Leave it at default settings.
Your RAM is running at an unusual frequency, what are the RAM settings in BIOS?

Post another CPUZ snip of the CPU, Mainboard, Memory, and SPD tabs.


Have you been checking your temperatures?
Use Real Temp , to check the CPU temps when at idle, under load and/or testing.
Let us know the minimum and maximum temps you get.
Go to your BIOS and tell us what the CPU, RAM and the CPU integrated memory controller voltages are.

 

[hdfsi]

Ok I have the Screen shots. I do not have anything for ram in my BIOS.
My temps.. No load its around 40-42 under load its 60-68.
My cpu/ram are on Auto for voltages.

 

[Dave76]

Is your 'Overclocking Navigator' set to 'Normal'?
If not then change it to Normal.

It is not recommended to use motherboard overclocking programs, they usually over volt and cause excess heat.
The OC's normally aren't very stable.

Select Manual to read the DRAM voltage and the CPU VTT voltage, post them in your next reply.

Set your DRAM Frequency to 1333MHz.

Set your 'DRAM Command Rate' to 2T.


Save and Exit your BIOS.

 

[hdfsi]

ok i went into bios i set DRAM Frequency to 1333mhz, Also set it to 2T.
But i saved it and booted and checked again and it still says my normal 666mhz.
i checked and i cant rly find the voltages besides on some weird page and it said they are, CPU-1.176v. DRAM-1.587v.

 

[hdfsi]

I also reset my cmos by moving the jumper and it is still not posting thats its set too 1333MHz.
Edit- Its now posting my CPU OC to 3.02GHz.