2 hard drives

[neverall]

on sata drive everisting is ok,on sata dvd rw ok,i have asus m2n,i have one ide disk,wd 80gb..win 7 is allready installed on sata drive...i dont know whats wrong,if i connect ide disk wd ,in bios listing is veeeery slow,it regognize disk and smart satus is ok,but i jaust cant boot normaly,dont know what to do ,i 99%% disk is ok,i need instruction on jumpers,cable,and how to install disk f*** drive..

 

[pooch]

Hello


Everything about WD Jumpers; How to physically install, set jumper settings, and set up a Serial ATA, EIDE, or SSD drive in Windows 7, Vista, XP, and 2000

The IDE disc needs to be set as slave

I hope this sorts the problem out

Edit you may find this helpfull; http://forums.tweaktown.com/gigabyte/38754-ud7-can-i-run-sata-ide-drives-same-time.html

 

[neverall]

Hello


Everything about WD Jumpers; How to physically install, set jumper settings, and set up a Serial ATA, EIDE, or SSD drive in Windows 7, Vista, XP, and 2000

The IDE disc needs to be set as slave

I hope this sorts the problem out

Edit you may find this helpfull; UD7 - can I run SATA and IDE drives at the same time?

no help good,i booted pc for 4 -5 minutes..wd 80 gb is set to slave.finaly booted ..now i just formated trough my computer/right click formate default.disk recognized ....why my boot takes f.....7 min! ....motherboar asus m2n....please tell me ,disk is 100% 0ok,cables too....whats wrong....

 

[pooch]

The edit was also no help?
If you remove the IDE drive does your PC boot quicker?

 

[1Bowtie]

You might also try cable select jumper setting on ide drive, did you do a clean install w/ Windows 7 or an upgrade.

 

[neverall]

You might also try cable select jumper setting on ide drive, did you do a clean install w/ Windows 7 or an upgrade.

without ide boots perfectly,i cant? put cable select,i ripeed of the end of the ribon cable,(with the blac plastic)if thats the name,so i soppose it must be slave,the gray playstic...,(the first one,i only have 1 ata cable)

 

[pooch]

You might also try cable select jumper setting on ide drive, did you do a clean install w/ Windows 7 or an upgrade.

without ide boots perfectly,i cant? put cable select,i ripeed of the end of the ribon cable,(with the blac plastic)if thats the name,so i soppose it must be slave,the gray playstic...,(the first one,i only have 1 ata cable)

If the cable is damaged you will have to replace it this might well be the cause of your problem

 

[1Bowtie]

I'm not fully understanding your last post, are you plugging the ide drive into the end of the cable or the middle?? if it's the end of the cable that's the primary, if the middle that's the slave. You might also go into bios and check the boot order and make sure your SATA hdd if first boot.

 

[neverall]

I'm not fully understanding your last post, are you plugging the ide drive into the end of the cable or the middle?? if it's the end of the cable that's the primary, if the middle that's the slave. You might also go into bios and check the boot order and make sure your SATA hdd if first boot.

ok,ireplaced cable,as said onto disk label it need 40pin as it is,last was i think 80,i think its the same for the purpose of work....it copies files very fast ,but boot still 5- min...

 

[neverall]

it bots from sata drive...not solved..any help?

 

[neverall]

You might also try cable select jumper setting on ide drive, did you do a clean install w/ Windows 7 or an upgrade.

clean install

 

[pooch]

i disableb ide contoroler in bios.where to downlaod another...

You need IDE or AHCI enabled in BIOS for the HDD's to work you cannot just download these things. Switching between IDE and AHCI is also not recomended
Have a look here; http://www.sevenforums.com/tutorials/61869-ahci-enable-windows-7-vista.html

 

[Sardonicus]

You have two controllers on the motherboard.
1. IDE controller
2. JMicron SATAII controller.

Many motherboards with two controller allow for each controller to be set to different modes.


Enable IDE for the 40 pin drive.
Enable the following, if not enabled already.


Enable the JMicron SATAII controller for the SATA drives and set to AHCI.

 

[neverall]

You have two controllers on the motherboard.
1. IDE controller
2. JMicron SATAII controller.

Many motherboards with two controller allow for each controller to be set to different modes.


Enable IDE for the 40 pin drive.
Enable the following, if not enabled already.
View attachment 154196

Enable the JMicron SATAII controller for the SATA drives and set to AHCI.

aus m2n dont have achi

 

[neverall]

help......i have asus m2n,sata disk is to boot ,wd ide is slave...boots 5 min..help!