Asus N76 UEFI - W7 64 Install Hangs on Logo (DVD UEFI Boot)

[theog]

Did clean the dvd allready. Also used an external dvd drive. I'm out of options. I guess i'm going to bring the laptop back where I purchased it.

I did some searching and I discovered this. See photo.
When in disk managment I went to OS C: properties. Then properties of disk and then tab volumes. There is nothing there. The SSD disk has info. Its has partitionstyle MBR. The normal HDD I first have to tick the box fill in so the info appears. I was forced a restart. Does this make sense?

CSM is not need as your Pre-installed Windows 7 is installed in Legacy mode already & booting.

It was a dual boot with old win7 on the HDD and a new win7 on the ssd. I used an upgrade version of win8 over the new win7 SSD. The old version of win7 still was there. Does Win8 change the way the disks behave?

1) The thread is about downgrading from Windows 8 Pre-installed to Windows 7.

2) Dual Boot Installation - Windows 8 and Windows 7 or Vista

3) Is the Windows 7 Pre-installed, installed in UEFI mode?

Try booting the Windows 8 Upgrade DVD.

 

[wim]

That was what I also thought, but the plan was to install it on the SSD. I'm going to try it. I will report later. Thanks for all the time you invested. Greatly appreciated!

 

[gregrocker]

Unplug all other HD's and peripherals,

Boot into BIOS setup, reset to defaults, save changes. If an EFI BIOS, enable Legacy BIOS or Compatibility Support Module, set DVD drive first to boot, HD second. Then set SATA controller to AHCI. Save changes and Exit.

Then boot into Win7 installer DVD or flash stick burned or written using tool and latest ISO for your licensed OS version here. The disk you have may be dirty or defective.

At first installer screen Press Shift + F10 to open a Command Box, type:

DISKPART
LIST DISK
SELECT DISK 0 (after confirming Windows 7 target HD #)
CLEAN
CREATE PARTITION PRIMARY SIZE=102400 (for 100gb partition, adjust as desired)
FORMAT FS=NTFS LABEL="WINDOWS 7"
ACTIVE
EXIT
EXIT

Next click Install Now, then Custom install to Clean Install Windows 7 to the partition you created. If it fails then report back at which step and the verbatim error message.

In addition read over these steps to understand the tools and methods which work best to get and maintain a perfect Clean Reinstall - Factory OEM Windows 7. The steps are the same for retail.

After install you can adjust partition size or Create new partitions for data, etc. in Disk Mgmt.You are creating the partition here for the purpose of marking it Active which overcomes certain install failures.You are trying now to install Win7 to the SSD, correct?

 

[Jodamensil]

Boas pessoal,
Comigo funcionou assim, entrei na bios, desactivei a opção secure boot no separador security, activei a opção launch csm no separador boot, gravei, reiniciei, carreguei na tecla para aparecer o menu de escolha de boot ( no meu é a tecla ESC ) e logo apareceu para escolher, pen, dvd,disco, etc...

Hello everyone,
With me it worked this way, in my bios e disabled the secure boot option in the security tab, i enabled the launch csm in the boot tab, saved and exit, and then i pressed the ESC key (wich is my key, yours can be diferente) and it show me, the ÛSB boot, DVD boot, HDD boot, and that way i manage to install the win 7 via a USB 3.0 drive.
Thanks to this fórum, in the page 4 on the 4th post.
Sorry for my bad english. From Portugal.

 

[bumblebeebart]

Hello all.
I have the same issue attempting to install Win 7 x64 on a Win 8 x64 pre-installed laptop. The laptop MEDIONshop Nederland | MEDION AKOYA E7221 laptop is equiped with 2 HDD/SSD drivebays and has excellent driversupport, including Win 7 drivers.
I felt it would be much more responsive running Win 7 from a SSD so bought the new Samsung 840EVO 120GB for that. Still had a WD Scorpio Blue lying around for data utalising the second drivebay.
The original HDD I took out just in case the laptop ever has to go back in factory conditions.
Then of course I ran into the same problems OP had.

Since the AMI bios also has the launch CSM and disable secure boot options listed, I now feel confident the transition will succeed.
Will let you know how I'll get on. Thanks in advance, best regards Bart.

 

[gregrocker]

Yes, a Win8 PC needs to have Secure Boot Disabled in BIOS setup as shown in Downgrade Windows 8 to Windows 7.

Special Install steps at UEFI (Unified Extensible Firmware Interface) - Install Windows 7 with - Windows 7 Forums.

Or if this presents problems you can Bypass UEFI to Install WIn7.

More about UEFI BIOS vs. Legacy BIOS - YouTube

 

[Gnaglor]

I'm having this exact same problem on a Dell Precision T1650. When legacy options are disabled, the Windows 7 installer hangs on the splash screen before ever loading the installer. I can install fine if it's Win 8 or if legacy options are enabled. I can't use legacy options though like the original poster. I need the OPROM free for a RAID controller I'm installing. Any ideas how to get this to work without using legacy?

 

[gregrocker]

Are you getting an EFI listing for your bootable installer when you boot in to choose it, as shown in UEFI (Unified Extensible Firmware Interface) - Install Windows 7 with - Windows 7 Forums.

If using a flash stick did you follow the special steps for UEFI Bootable USB Flash Drive - Create in Windows ?

 

[Gnaglor]

I fixed this problem for myself. LSI said the card needs to have the OPROM available, which is the resource Windows needs and gives the error code 10 on. When I switched to UEFI mode and left legacy option roms available it still wouldn't work. When I switched to UEFI and then turned off legacy option roms then it worked. I have an Optiplex 790 sitting around which is basically an older T1650 and the bios on that machine didn't have the option to turn off legacy boot roms. I could switch between UEFI and legacy boot mode, but there was no option to turn off legacy roms. In the T1650 bios, there is an option for switching boot modes and a seperate option for disabling legacy option roms. The two are distinctly different. It's possible you'll only have the option to switch between boot modes, in which case the bios may still have a handle open to the legacy option roms, even though you've switched to UEFI boot mode. If that's the case, look for a bios update (the 790 had the most up-to-date) and hope that will give you the option. Otherwise I don't believe there is anything you can do other than get a new card or a new motherboard.

 

[gregrocker]

You said that you'd disabled Legacy Options in BIOS. Disabling Legacy Mode or CSM choices should be sufficient to enable UEFI install.

That's why I asked if you have UEFI boot choices for your installer. Did you try the UEFI DVD boot?

You'll always have to choose your boot device when installing, using either the BIOS Boot Priority order choices, or the one-time BIOS boot Menu key at boot.

 

[Gnaglor]

"You said that you'd disabled Legacy Options in BIOS. Disabling Legacy Mode or CSM choices should be sufficient to enable UEFI install.

That's why I asked if you have UEFI boot choices for your installer. Did you try the UEFI DVD boot?

You'll always have to choose your boot device when installing, using either the BIOS Boot Priority order choices, or the one-time BIOS boot Menu key at boot."

Not sure if you're referring to my post, but just changing to UEFI and leaving legacy boot options enabled was not enough to get the card to work. The card needs to have the legacy options disabled in order for the handle to be open for Windows to use it. I've switched to UEFI mode and left legacy option roms enabled and after Windows is installed (7 or 8), the card error code 10's. If you then disable legacy option roms, even though the partition is EFI, Window's will then fail to boot. The install has to be done with legacy options disabled from the beginning.

My problem now is that I can't get Windows 7 to install. 8 works fine, but the 7 installer stops doing anything on the Starting Windows splash screen. I've tried three different discs and two different computers. I'm working on this with Dell, not the point of this posting.

The point of this posting is to say that at least on Dell's, you have to switch to UEFI and disable legacy option roms for the 9240 to work. I've seen machines that allow you to switch between UEFI and legacy boot mode that don't have the option to disable legacy booting and those are hit or miss on whether or not the card will work. I've seen it work on an Optiplex GX620, but not on an Optiplex 745 or a 7010.

 

[gregrocker]

If you want to quote someone click the Quote button on their post. That's why the Quote button is there.

Did you try to Bypass UEFI to Install WIn7 yet?

 

[Gnaglor]

If you want to quote someone click the Quote button on their post. That's why the Quote button is there.

Did you try to Bypass UEFI to Install WIn7 yet?

I can't bypess UEFI. I have to use it.

I tried turning on the legacy rom's, booting the 7 installer, using disk part to create a gpt partition, but then the installer says "Windows cannot be installed to this disk. The selected disk is of the GPT partition style."

Tried this as well.

http://technet.microsoft.com/en-us/library/hh825686.aspx#ConfiguringPartitionsUsingDiskPart

I am currently installing 7 with legacy options enabled, but switched to uefi booting. The only boot device allowed is the UEFI DVD and the 7 installer is letting me install to the GPT partition I created with the technet link. I'm pretty sure this won't work and when I disable legacy ROMs, 7 will stop booting, but I'll let you know for sure when the install is done.

 

[Gnaglor]

My above posting didn't work. After 7 was installed the 9240 produced the predictable error code 10. I turned off legacy option ROMs and could then no longer boot into 7. I've also since tried installing 7 to a UEFI only motherboard of a custom build machine my friend has. I can't be certain his legacy options were disabled completely as there was no specific option like the Dell BIOS. Only to choose UEFI only. I did an install on his machine and then put the drive in the Dell and it failed to boot. In talked with Dell, they sent me one of their own Windows 7 x64 w/ SP1 discs to try as well as a link that I had already been to.

Installing Windows 7 on UEFI based computer - Ask the Core Team - Site Home - TechNet Blogs

Then said this.

"Just to make sure, here is a link to how this is supposed to be done. There is only 1 step that is different from a regular reinstall. If this does not work, then the issue sounds like a UEFI issue since it is happening across several platforms ."

The several platforms are a Dell T1650, a Dell Optiplex 7010, and a Dell Optiplex 745.

I like how they blame a universal standard and not their equipment.

 

[gregrocker]

If you want to install to UEFI then you need to disable Legacy BIOS (which you said you enabled) use the special steps in UEFI (Unified Extensible Firmware Interface) - Install Windows 7 with - Windows 7 Forums deleting all partitions at the drive selection screen, or wiping the HD first with Diskpart Clean Command.

If you want to Bypass UEFI to Install WIn7 then you'll need to enable Legacy BIOS or CSM, disable Legacy if it has a separate BIOS setting, also wipe the HD as shown in the steps in blue link.

Just to be sure, reset the BIOS to defaults before trying each way.

If these both fail then please post back camera snaps of all the BIOS choices for UEFI and Legacy, including the Boot options for either mode. Screenshots and Files - Upload and Post in Seven Forums - Windows 7 Forums

 

[Gnaglor]

So I've come to the conclusion that this card just isn't going to work with my particular system. The card will always error code 10 in Win 7 or Win 8 (x64 for both) if legacy option ROMs are enabled. If they aren't enabled, I can't boot Windows from a previous install with them enabled and I can't do a fresh install of Windows 7 (the OS I need to have installed) because the installer locks up when trying to load. This is a separate problem I've been working with Dell on.

"On Mon, Oct 7, 2013 at 1:21 PM, wrote:

I will wait for your reply on this. Just to make sure, lets do all troubleshooting with onboard only and do not use any additional cards until we can figure out what the issue is. This all could be a limitation of our hardware with UEFI and we will need to wait for a proper BIOS update to resolve this. I have been talking to several other agents, Seniors, and managers about this and all is showing it should work with Secure Boot off while running on the onboard card. As for the LSI card we are not sure as we do not use that card on the system.



Thank you for choosing Dell,

M-F 7:30AM-4:30PM
Dell Workstation
1877-671-3355<tel:1877-671-3355>
Dell Drivers/Downloads: Product Selection | Dell US "

That's one of my most recent messages from them.

I can install Win 8 with only UEFI and legacy option ROMs disabled, and the card does work in Win 8, no error code 10, but that's when something else I noticed hit me. When legacy option ROMs are disabled, when the computer boots, it no longer loads the 9240's firmware or whatever the correct term would be. Usually (when legacy is enabled) before I can access the computers BIOS or before it starts to try and PXE boot or anything, the 9240 will take over the legacy option ROM and load itself in, checking for any attached drives and gives you a chance to modify any of its settings through a GUI or CLI. With legacy disabled, it just skips over this and when I get into Win 8 (for testing purposes), the card works, but I can't see any attached drive.

My current goal is to see if there's now some LSI software that will allow me to get the drives up in Win 8 with legacy disabled and a successful Windows install of the card. Unfortunately my managers, seniors, etc., have decided they are going to return the equipment and I don't have much time left to try things out.

 

[gregrocker]

Please reply to the steps I gave you.

Sometimes it requires CSM or Legacy to install Win7 in UEFI mode at all.

If UEFI doesn't work for you with Legacy or any CSM listings enabled or disabled, then try to Bypass UEFI to Install WIn7 with UEFI disabled, Legacy or CSM fully enabled.

If neither works then try another card.

 

[Gnaglor]

I appreciate the help, but this card just isn't going to work with this machine.

With legacy options enabled, the card takes over the option ROM and Windows doesn't have access to the ROM in order to successfully install. I can install Windows, but I can't use the card, error code 10. With legacy disabled, I can't even install 7, the installer won't load, something Dell has said they may need a BIOS update for. I can install 8 and the card installs in 8 with legacy disabled, no error code 10, but you can't see any attached drives. Also, with legacy disabled, I can no longer access the cards built-in GUI or CLI to set up RAID and make all sorts of configuration changes before the computer boots. Because legacy is disabled, it just doesn't even give the card a chance to tell the computer it's there on boot up. Windows knows it's there because it's installed in the PCIe slot, but because legacy ROMs are disabled on the motherboard, it can't properly interact with the card because it never got the chance to initialize itself on boot up.

It's all a mute point now anyways. The superiors only wanted the cards to run 15000rpm SAS drives to store large data files for a sever training class (this is a community college). Why they thought spending 10K plus for this without testing it is beyond me, but they are returning everything they can and buying regular SATA drives, so I can't work on it anymore. I still wanted to see if there was LSI software I could run in Windows 8 to see and manipulate attached drives or just use legacy to load the cards GUI, create a virtual partition, install 7 to it, and see if that worked. But alas, we'll probably never know at this point.

Thanks again for the help, sorry I couldn't continue to work on it.

Btw, I tried the link you provided, as well as a few others that involved using diskpart, and none of them worked for the reasons described above. Even when I did successfully get an EFI install in 7, the card won't work because of what I said above. When I turn off legacy after the successful install, Windows will error on boot. So the problem isn't that 7 (or 8) won't install UEFI, it's that 7 won't install without legacy enabled and the card won't work (or will work and not see attached devices) if legacy is enabled or disabled. I.e. the card doesn't work with this system; at least not without possible software by LSI or installing Windows to an attached device instead of a drive connected to the motherboard.

 

[gregrocker]

Thanks for clarifying. Be aware we see nothing but problems here with RAID since Win7's release. I would avoid it unless the benefits are known to outweigh the pitfalls which are manifold.

 

[bumblebeebart]

Back again. Enabling CSM & disabling Secureboot worked just fine. Also upped the RAM from 4 to 8GB. Combined with the new SSD I have a fast responsive Win7 laptop now. Once experienced, you never want to go back to HDD. The performance gain is astonishing and really worth shelling out some €.