Solved BSOD on computer after motherboard upgrade

[Anthony07]

Ok i will update in a few days or if something happens sooner i am runing system stability test right now on aida64 its run for 8 hour so far no crashes thanks so much for your help so far

 

[essenbe]

Great, what temps are you seeing? Be sure to keep a close watch on your CPU temps.

 

[Anthony07]

I see anywhere from 50 to 52 c on cpu and like 59 on mainboard

 

[essenbe]

That sounds good. Just let me know how it comes out or if you need help.

 

[Anthony07]

Ok i left test run for bout 20 hours no crashes so far i have now stopped test no problems to report so far any other ideals on things to test for stability

 

[essenbe]

I don't recall what you've run, but I remember you running memtest.

So, run Seatools for DOS http://www.sevenforums.com/tutorials/313457-seatools-dos-windows-how-use.html#Part3

And get a good GPU monitoring program and run Furmark http://www.sevenforums.com/tutorials/100356-video-card-stress-test-furmark.html But, keep a close watch on temps and stop the test if they get too high.

 

[Anthony07]

Ok i have run the gui based seatools for windows is there a difference between that and the dos one i will also check the gpu i only have onboard graphics right now will that make any difference
Dont get me wrong if there is something different bout the gui and dos version let me know i will run it if need be

 

[Anthony07]

Also meant to ask why would windows intall amd 760g as the default driver for graphics instead of the radeon hd 3000 driver thats is meant for motherboard with amd

 

[essenbe]

DOS is basically the same test, It's just run out of ram while the hard drive is not in use and gives better results because of that. As far as your graphics, you are using on board graphics and I imagine your graphics is controlled by the chipset driver, which I suspect you have a 760 chipset. I'm just assuming here, but you don't have a dedicated card so the CPU contains your graphics. Look at the web site for your motherboard and see what drivers they have.

You could run a graphics test but I don't think that is a good idea with on board graphics.

Just see how it goes from here. If you get any more BSODs, upload them and we'll see what they say.

 

[Anthony07]

Ok thank you so much i will try the dos test on hard drive to make sure hard drive is good i will check computer out for few days and let you know if anything strange happens or upload any subsiquent bsods if any

 

[essenbe]

OK, sounds good.

 

[Anthony07]

Ok so i have been running computer for last few days straight i have yet to c another bsod so for now i am gonna mark this as solved if i have any more issues i will open a new forum thanks so much for your help essenbe and profdlp

 

[essenbe]

That sounds great. I hope your good luck continues. If you have further problems, you can post here or start another thread and link to this one. Good job.

 

[Anthony07]

bsod again

ok so i am back again guys unfortunately after leaving computer set for a few days off i went to turn on pc today and what do ya know first thing it does is blue screen i am uploading new dm log collector which has bsod dmp file

 

[essenbe]

This is all I could find

IRQL_NOT_LESS_OR_EQUAL (a)
An attempt was made to access a pageable (or completely invalid) address at an
interrupt request level (IRQL) that is too high.  This is usually
caused by drivers using improper addresses.
If a kernel debugger is available get the stack backtrace.
Arguments:
Arg1: 00000001009b66f0, memory referenced
Arg2: 0000000000000002, IRQL
Arg3: 0000000000000001, bitfield :
 bit 0 : value 0 = read operation, 1 = write operation
 bit 3 : value 0 = not an execute operation, 1 = execute operation (only on chips which support this level of status)
Arg4: fffff800034c69a3, address which referenced memory
Debugging Details:
------------------
 
WRITE_ADDRESS: GetPointerFromAddress: unable to read from fffff800036f6100
GetUlongFromAddress: unable to read from fffff800036f61c0
 00000001009b66f0 Nonpaged pool
CURRENT_IRQL:  2
FAULTING_IP: 
nt!KiTimerWaitTest+2b3
fffff800`034c69a3 48894108        mov     qword ptr [rcx+8],rax
CUSTOMER_CRASH_COUNT:  1
DEFAULT_BUCKET_ID:  WIN7_DRIVER_FAULT
BUGCHECK_STR:  0xA
PROCESS_NAME:  [COLOR=red]Zentimo.exe[/COLOR]

You've been getting a lot of errors from Crysis too.

 

[Anthony07]

Ok so new question i am really starting to get confused now why does it seem like i am having problems with all these different programs which i never had any problems with on my last mother board is there some sort of reason that you can think of

 

[essenbe]

No. I don't really think it's the Motherboard. It's more like the programs with drivers conflicting with each other. The games seem to always cause problems, for some reason. I used to get a ton of errors and crashes with BF4.

 

[Anthony07]

Thats the thing i dont have any games installed i dont even play any on the computer

 

[Layback Bear]

Might be of some interest.

Zentimo.exe Windows process - What is it?

I'm back to watching.

 

[essenbe]

You show about 20-30 errors for crisis.exe on 12/31